Publicité
Page 6 of 13
Referring to the RHS Assembly
•
head bolt (item 6) and M10 Washer (item 8), fix the RHS Crash protector bracket (item 2) into
place, ensuring the standoff sits into the frame recess and supporting tabs cup the frame as shown
in Picture 6. Note the thinner section of the bracket should sit between the radiator support bracket
and frame.
NOTE: To avoid cross threading apply forward pressure to the bolt and rotate counter-
clockwise until a click is heard then begin to turn clockwise & tighten.
•
While holding the bracket in place so it is central to the frame, tighten the M10 bolt to the
recommended specification.
Place one M10 bolt head cap (item 11) onto the head of the bolt.
•
For both sides
•
Ensuring both replacement engine bolts are correctly torqued, remove the jack from under the engine
Re-fit all fairing to the bike as originally removed, the crash protector mounts should be visible as
•
shown in picture 7.
Following the assembly diagram for each side, fit one M10x20 washer (item 8) over the M10x80mm
•
cap head bolt (item 7) and slide one crash protector (item 3) followed by one of the 36mm spacers
(item 4) so that the head of the bolt sits inside the crash protector and offer up to the exposed boss
of the crash protector bracket as shown in Picture 7.
Fit the crash protector into the exposed boss on each side and torque to the recommended
•
specification on page 2.
Finally, place one M10 Cap head bolt cap (item 10) into each crash protector as shown in Picture
•
8.
•
Before riding, check both sides are secure.
Please note: Torque of the engine/crash protector bolts should be checked at regular intervals
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and
suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and
care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that
the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its
option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or
used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the
defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death
and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts
paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns
of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to
faulty goods.
Unit
Tel: +44 (0)
when doing routine maintenance/servicing.
ISSUE 1 – 24/09/2024 – DM
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
420 89007
www.rg-racing.com
1
diagram, Using the M10x70mm Hex
R&G
Email:
info@rg-racing.com
CP0575
Publicité
