Publicité
Liens rapides
Page 1 of 13
CP0575
FITTING INSTRUCTIONS FOR CP0575 CRASH PROTECTORS
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G
Unit
, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
Tel: +44 (0)
420 89007
www.rg-racing.com
Email:
info@rg-racing.com
1
Publicité
Manuels Connexes pour R&G CP0575
Sommaire des Matières pour R&G CP0575
- Page 1 Page 1 of 13 CP0575 FITTING INSTRUCTIONS FOR CP0575 CRASH PROTECTORS HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
- Page 2 Page 2 of 13 CP0575 GENERAL TORQUE SETTINGS TOOLS REQUIRED M4 BOLT = 8Nm Torque Wrench • M5 BOLT = 12Nm Scissor Jack • M6 BOLT = 15Nm 14, 17mm & 19mm Sockets and Ratchet • M8 BOLT = 20Nm Set of Metric Allen Keys •...
- Page 3 Page 3 of 13 CP0575 LHS ASSEMBLY RHS ASSEMBLY R&G Unit , Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0) 420 89007 www.rg-racing.com Email: info@rg-racing.com...
- Page 4 Page 4 of 13 CP0575 PICTURE 1 PICTURE 2 PICTURE 3 PICTURE 4 PICTURE 5 PICTURE 6 R&G Unit , Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0) 420 89007 www.rg-racing.com Email: info@rg-racing.com...
- Page 5 Page 5 of 13 CP0575 PICTURE 7 PICTURE 8 FITTING INSTRUCTIONS IMPORTANT: Before removing engine bolts, ensure the bike is upright and supported by a suitable engine stand or jack placed under the sump of the motorbike to support the partial weight of the engine, this will prevent the engine from moving during fitting.
- Page 6 Page 6 of 13 CP0575 Referring to the RHS Assembly diagram, Using the M10x70mm Hex • head bolt (item 6) and M10 Washer (item 8), fix the RHS Crash protector bracket (item 2) into place, ensuring the standoff sits into the frame recess and supporting tabs cup the frame as shown in Picture 6.
- Page 7 Page 7 of 13 CP0575 NOTICE DE MONTAGE CP0575 PROTECTIONS CRASH E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N...
- Page 8 Page 8 of 13 CP0575 VALEURS DE SERRAGE OUTILS REQUIS M4 BOULON = 8Nm Clé dynamométrique • • Cric à ciseaux M5 BOULON = 12Nm Clé à cliquet + douilles 14, 17mm & • 19mm M6 BOULON = 15Nm Clés Allen •...
- Page 9 Page 9 of 13 CP0575 ASSEMBLAGE CÔTÉ GAUCHE ASSEMBLAGE CÔTÉ DROIT R&G Unit , Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0) 420 89007 www.rg-racing.com Email: info@rg-racing.com...
- Page 10 Page 10 of 13 CP0575 PHOTO 1 PHOTO 2 PHOTO 3 PHOTO 4 PHOTO 5 PHOTO 6 R&G Unit , Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0) 420 89007 www.rg-racing.com Email: info@rg-racing.com...
- Page 11 Page 11 of 13 CP0575 PHOTO 7 PHOTO 8 NOTICE DE MONTAGE IMPORTANT : Avant de retirer les boulons du moteur, assurez-vous que la moto soit en position verticale et soutenue par un support moteur ou un cric approprié placé sous le carter de la moto pour supporter le poids partiel du moteur, cela empêchera le moteur de...
- Page 12 Page 12 of 13 CP0575 • Une fois le moteur entièrement soutenu comme indiqué sur la photo 1, retirez le boulon du moteur indiqué par une flèche sur la photo 5. Présentez le support de protection crash côté droit (article 2) et notez les endroits où il pourrait y •...
- Page 13 Page 13 of 13 CP0575 R&G RACING RETURNS POLICY (NON-FAULTY GOODS) Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing.