Mounting The Grass Catcher Tipping Levers; Mounting The Side Guards Of The Cutting Device Assembly (If Any); Side Discharge Chute Assembly (For Models With Side Discharge Only); Controls - EMAK KTK 102H Série Manuel D'utilisation

• TS-TX-TH models
Complete the grass catcher mounting
sequence as described in the instruction
sheets supplied with the components.
4.9 MOUNTING THE GRASS
CATCHER TIPPING LEVERS
Position the lever shaft (fig. 10.A) so
that it lies in the groove in the two plates
(fig. 10.B) and secure it to the inner
part of the grass catcher bag supports
(fig. 10.C), using the nuts and bolts (fig.
10.D) supplied in accordance with the
sequence indicated in the figure.
Connect the end of the lifting piston
shaft (fig. 10.E) to the lever (fig. 10.F)
by using the pin (fig. 10.G) and mount
the two elastic rings (fig. 10.H).
Before mounting the grass catcher
bag on its support, make sure that
tipping levers move correctly.
4.10 MOUNTING THE SIDE GUARDS
OF THE CUTTING DEVICE
ASSEMBLY (IF ANY)
Mount the safety panels (fig. 11.A) using
the screws (fig. 11.B) and nuts (fig. 11.C)
supplied, in accordance with the instructions
provided for each machine type.
4.11 SIDE DISCHARGE CHUTE
ASSEMBLY (FOR MODELS WITH
SIDE DISCHARGE ONLY)
1. From the inside of the side discharge
chute (fig. 12.A), fit the spring (fig.
12.B) by inserting the terminal (fig.
12.B.1) into the hole and turning it so
that both the spring (fig. 12.B) and
the terminal (fig. 12.B.2) are securely
positioned in their housings.
2. Position the side discharge chute (fig.
12.A) in line with the cutting device
assembly brackets (fig. 12.C). Using a
screwdriver, turn the second terminal (fig.
12.B.2) of the spring (fig. 12.B) to bring
it outside the side discharge chute.
3. Fit the pin (fig. 12.D) in the holes
on the brackets (fig. 12.C) and on
the side discharge chute, so that it
passes through the coils of the spring
(fig. 12.B) and the drilled end comes
out of the inner most bracket.
4. Insert the cotter pin (fig. 12.E) into
the hole (fig. D.1) on the pin (fig. 12.D)
and rotate the pin in order to bend
the two ends (fig. 12.E.1) of the cotter
pin, (with the aid of a pair of pliers),
so that it cannot slide out, causing
the pin (fig. 12.D) to disengage.
Check that the spring works
correctly and keep the side discharge
chute securely lowered. Make sure
that the pin is fitted properly to prevent
it from falling out accidentally.
IMPORTANT
side unloading: make sure that the side
unloading guard (Fig. 21.A) is lowered and
locked by the safety lever (Fig. 21.B).
IMPORTANT Before disassembling or
servicing the deflector, always push the safety
lever (Fig. 21.B) and lift the side unloading
guard (Fig. 21.A) to allow disassembly.
NOTE To remove the deflector, perform
assembly steps in reverse order.

5. CONTROLS

5.1 BRAKE PEDAL

This pedal operates the brakes on
the rear wheels (fig. 13.A, 14.A)

5.2 FORWARD GEAR PEDAL

This pedal is used to apply traction to the
wheels and regulate the speed of the machine
when it is moving forward (fig. 13.B, 14.B):
1. Forward drive gear. Increasing
EN - 9
For models with optional
the pressure on the pedal
progressively increases the
speed of the machine.