Publicité
dentally slipping off the forearm support.
5. The width between the forearm supports can be ad-
justed by removing and repositioning the clamps and
adjusting rods.
• Step 1: Loosen the screw (K) and remove the forearm
support.
• Step 2: Press the button (L), pull out the adjusting rod,
and rotate in the desired position.
• Step 3: Place the forearm support back onto the adjust-
ing rod and tighten the screw (K). Steps 1 and 2 show the
position of the clamp on the inside of the upper frame.
Step 3 shows the position on the outside which increas-
es the distance between the arm supports (photo. 19).
Hip belt
(S = Art. no.: TK1080S; M = Art. no.: TK1080M; L = Art. no.:
TK1080L)
1. To adjust the width of the hip belt, the clamps can be
attached to the inside or outside on the upper frame
(photo. 9/10). Then the lateral holders can be moved
inwards or outwards by loosening the screw (S).
2. To adjust the height, press the button (T), adjust to the
desired height, and release the button. The adjusting
rod is correctly snapped into place when the button
audibly clicks into place.
3. By loosening the screw (T) the hip belt can be adjusted
forward or backwards on the frame or completely re-
moved, as shown in photo 20.
20
V
S
T
Seat harness
(S = Art. no.: TK1070S; L = Art. no.: TK1070L)
1. To adjust the height of the rear part of the seat, press
the button (X), adjust to the desired height, and release
the button. The adjusting rod is correctly snapped into
place when the button audibly clicks into place.
2. By loosening the screw (Y) the rear part of the seat
can be adjusted forward or backwards on the frame or
completely removed, as shown in photo 21.
3. The belt buckles (Z) are used to secure the front and
rear part of the seat. Secure the front belt fasteners as
desired. Attach the rear belt fasteners on the adjusting
rods for additional height adjustment as shown or di-
rectly on the upper frame (the caps on the end prevent
Drive Medical GmbH & Co. KG | As per: 19.03.2024 | Errors and alterations excepted
4. The four straps (V) can
be used individually for
adjustment or loosening
or to change the angle of
the forward-inclined posi-
tion (photo. 20).
the belts from slipping off the frame).
21
Y
4. The belt buckles (A) are used to adjust the height of
the seat (photo. 21).
Thigh strap
(S = Art. no.: TK1090S; L = Art. no.: TK1090L)
22
E
1. The thigh strap can be adjusted towards or away from
the user by loosening the screw (B). Retighten the
screw.
2. The height or angle of the thigh strap can be adjusted
by loosening the screw (C).
3. By loosening the screw (D) the thigh strap can be ad-
justed forward or backwards on the frame or complete-
ly removed, as shown in photo 22.
4. The strap can be applied to or adjusted at the thigh
using the belt fastener (E) (photo. 22).
Ankle wrap
(S = Art. no.: TK1060S; M = Art. no.: TK1060M; L = Art. no.:
TK1060L)
1. The strap can be applied to or adjusted at the ankle
using the belt fastener (F)
2. The step guidance can be adjusted by pressing and
moving the clamp springs (G) on the rods.
3. The ankle wrap can be completely removed by moving
the clamp springs (H) away from the wheel, as shown
in photo 23.
EN
N
X
A
D
B
C
Instructions for use TREKKER GT
17
Publicité
