Publicité
Connect the earth cable to the Negative output
terminal (Minus) -
C
the earth clamp to the workpiece.
Plug the torch hose into the socket -
of the welder having care to not damage the contacts
and secure by hand screwing in the threaded con-
nection.
Only by models with water cooling: connect the water
feed and return hose of the torch to the water cooling
connections -
-.
G
2T/4T MODE
•
Enable the 2T/4T selection mode (L13 or L14
blinking) through the T3 key.
•
Change the mode though the E2 key. Value is
displayed on D2.
•
Press T2 to confirm.
INDUCTANCE
•
Enable the inductance setting (L15 blinking)
though the T3 key.
•
Adjust the value through the E2 Knob. Value
is displayed on D2.
•
Press T2 to confirm.
SPOT
•
When spot welding control is active, it is pos-
sible to enable the setting of the spot welding
time though the T3 key.
•
Adjust the value through the E2 Knob. Value,
variable from 0 to 10,0'', is displayed on D2.
•
Press T2 to confirm.
PARAMETERS DISPLAYING
•
Change the displaying of the welding parame-
ter on D1 and D2 by pressing the T1 key and
choosing the parameter through E1 and E2.
•
In Synergic MIG mode L1, L2, L3 and
L7, L8, L9 will light up according to the
selected parameter.
•
In Manual MIG mode, only wire speed
and welding voltage can be adjusted.
MANUAL MIG WELDING (JOB LIST 10)
The unit is supplied from the factory in Manual MIG
mode (JOB LIST 10).
In this mode, it is only possible to adjust, through
E1 and E2, the voltage and wire speed values, in
addition to the inductance.
SYNERGIC MIG WELDING (JOB LIST 11-99)
•
By holding T1 it is possible to enter the JOB
LIST (Synergic MIG).
•
Use E2 to select the desired JOB (D1 displays
the job description, D2 displays the job num-
ber) and confirm the selection through T2.
Note: the list of synergic curves can be found inside
the wire spool compartment.
MIG/MAG WELDING
MIG WIRE WELDING
- on the front of the unit and
- on the front
A
JOB LIST • SINERGY
MATERIAL
WIRE Ø
MIG MANUAL
Fe
0,8
Fe
0,9
Fe
1,0
Fe
1,2
Fe
1,6
CrNi - 308
0,8
CrNi - 308
0,9
CrNi - 308
1,0
CrNi - 308
1,2
CrNi - 316
0,8
CrNi - 316
0,9
CrNi - 316
1,0
CrNi - 316
1,2
0,9
AlMg
- 5356
5
1,0
AlMg
- 5356
5
1,2
AlMg
- 5356
5
Fe Metal
1,2
Fe Rutil
1,2
CuSi
0,8
3
Table 2
To enter the
"Job list"
press and hold for 5 sec the
The synergic programs are continuously
the control panel.
updated, also refer to the JOB LIST table on
Once the menu appears on the screen, select the desired curve
the machine.
MODE key
between the
MIG torch
button.
RADID SETUP MENU - MIG
•
In MIG mode (L10 ON) hold the T3 key for 5s
at least to change the parameters (PRE GAS,
SLOPE, BBT and POST GAS.)
•
Select the desired parameter through E1 and
change the value through E2.
Pre Gas:
(from 0 to 10s) DEFAULT value 0.0s
SLoPE:
Wire feeder motor acceleration slope (from
0 to 2.5 s) DEFAULT value 0.0s
bbt:
Burn Back Time (from 1 to 100). DEFAULT value
50
PoST GaS:
(from 0 to 25s) DEFAULT value 3.0s
"CONSTANT VOLTAGE" FUNCTION
This function is suitable for the special wire feeders
(different from the standard wire feeder) powered by
the power source. Voltage must be adjusted on the
power source according to the welding wire type and
diameter, wire speed on the wire feeder.
•
Hold T5 key for 3s, release the key and hold
it again for other 3s to enable the CV fun-
ction. L23 LED remains ON, D4 displays the
welding voltage that is adjustable through the
E3 knob.
•
Press T5 to display the inductance value (L22
ON). Change the value through E3 (Value
from 0 to 50). DEFAULT value 25
EN-13
M21
M12
C1
MIX
MIX
CO
80% 20%
98% 2%
100%
2
10
10
10
12
-
18
13
-
19
14
-
20
15
-
21
16
-
-
-
25
-
-
26
-
-
27
-
-
28
-
-
30
-
-
31
-
-
32
-
-
33
-
-
-
-
-
-
-
-
-
-
45
-
-
47
-
50
-
-
-
menu:
JOB LIST key
on the top center of
Save&Recall
key, or by clicking the
or the
I1
Argon
100%
10
-
-
-
-
-
-
-
-
-
-
-
-
-
39
40
41
-
-
60
Publicité
