Publicité
FEHLERBEHEBUNG ................................................................................................................................... 29
PREFACE (EN) ................................................................................................................................................. 31
SAFETY................................................................................................................................................................. 32
13.1
Intended use of the machine ............................................................................................................................................... 32
13.1.1
Technical Restrictions .......................................................................................................................................................................................... 32
13.1.2
Prohibited Use / Forseeable Misuse ........................................................................................................................................................... 32
13.2
User requirements ....................................................................................................................................................................... 32
13.3
Safety devices ................................................................................................................................................................................. 33
13.4
General safety instructions .................................................................................................................................................... 33
13.5
Electrical safety .............................................................................................................................................................................. 34
13.6
Special safety instructions for that machine .............................................................................................................. 34
13.7
Hazard warnings ........................................................................................................................................................................... 34
TRANSPORT ..................................................................................................................................................... 35
ASSEMBLY ........................................................................................................................................................ 36
15.1
Check scope of delivery ............................................................................................................................................................ 36
15.2
Requirements for the place of installation .................................................................................................................. 36
15.3
Preparation of the surface ...................................................................................................................................................... 36
15.4
Assembling the machine ........................................................................................................................................................ 36
15.5
Electrical connection ................................................................................................................................................................. 37
15.5.1
Setting up a 400 V machine ........................................................................................................................................................................... 38
15.6
Connecting to a dust collection system ........................................................................................................................ 38
OPERATION ..................................................................................................................................................... 39
16.1
Operating instructions .............................................................................................................................................................. 39
16.2
Initial check before start .......................................................................................................................................................... 39
16.3
Settings ............................................................................................................................................................................................... 39
16.4
Operation .......................................................................................................................................................................................... 40
16.4.1
Switch the machine on and off .................................................................................................................................................................... 40
16.4.2 Activating/Deactivating the thicknesser feed rate ......................................................................................................................... 40
16.5
Dust collection plug .................................................................................................................................................................. 40
16.6
Planing ................................................................................................................................................................................................. 41
16.6.1
Planing small workpieces .................................................................................................................................................................................. 41
16.6.2 Planing with tilted planer fence ................................................................................................................................................................... 42
16.6.3 Planing short workpieces .................................................................................................................................................................................. 42
16.6.4 Planing the workpiece with small cross section ............................................................................................................................... 42
16.7
Thicknessing .................................................................................................................................................................................... 42
16.7.1
Converting from planer to thicknessing ................................................................................................................................................. 43
16.7.2 Thicknessing of workpieces ............................................................................................................................................................................. 43
16.8
After working process .............................................................................................................................................................. 44
OPERATION MORTISING UNIT (OPTIONAL) ............................................................................. 44
17.1
After working process ............................................................................................................................................................... 45
CLEANING, MAINTENANCE, STORAGE, DISPOSAL ............................................................. 45
18.1
Cleaning ............................................................................................................................................................................................. 45
18.2
Maintenance .................................................................................................................................................................................... 45
18.2.1
Maintenanceplan .................................................................................................................................................................................................... 45
18.3
Checking/adjusting/replacing the V-Belt ....................................................................................................................46
18.4 Lubricate height adjustment (thicknesser) ................................................................................................................46
18.5
Check/clean anti-kick-back device ...................................................................................................................................46
18.6
Check/replace friction wheel (feed) .................................................................................................................................46
18.7
Check/lubricate chain-drive (feed) ...................................................................................................................................46
18.8
Replacing/adjusting the planing knife (HOB410PRO) ......................................................................................... 47
18.9
Replacing/turning the cutter insert (HOB410PROSMW4) ................................................................................ 47
18.10 Storage ............................................................................................................................................................................................... 48
18.11 Disposal .............................................................................................................................................................................................. 48
TROUBLESHOOTING ................................................................................................................................. 48
AVANT-PROPOS (FR) ................................................................................................................................ 50
SECURITE ............................................................................................................................................................ 51
21.1
Utilisation conforme .................................................................................................................................................................... 51
21.1.1
Restrictions techniques ....................................................................................................................................................................................... 51
21.1.2
Applications interdites / Mauvaises applications dangereuses ............................................................................................... 51
21.2
Exigences des utilisateurs ....................................................................................................................................................... 51
HOLZMANN MASCHINEN GmbH www.holzmann-maschinen.at
INHALT / INDEX
HOB410PRO_400V | HOB410PROSMW4_400V
3
Publicité
