Publicité
May we congratulate you on your new greenhouse
GB
Dear Customer!
DEAR CUSTOMER
Congratulations on purchasing your new
The assembly of your new house requires
greenhouse. It is important that you follow these
a bit of technical knowledge. However, it is
assembly instructions step-by-step.
important that the assembly instructions are
followed strict-ly. The assembly instruction
The assembly instructions are a combination of text
is a combination of text and illustrations. The
and illustrations. The profiles are packed in separate,
profiles are packed in separate numbered packs
numbered packs corresponding to their order of use
corresponding to the order in the assembly
in the instructions. Assemble one pack at a time.
All nuts, bolts and fittings are contained in bag No.
instruction. Erect one pack at a time. All nuts
0 (specified on page 12). Each pack is specified in
and bolts and fittings are found in bag No. 0
separate lists of components.
(specified on page 12). Each pack is specified in
All detailed illustrations are marked with the
separate lists of components.
following symbols:
All detailed illustrations are marked with
symbols:
Seen from the inside
Seen from the outside
Seen from inside
Seen from outside.
SOME SAFETY PRECAUTIONS
•
Assembly must only be carried out in dry and
calm weather.
Precautions.
•
Always wear work gloves when installing the
•
Assembly must only be carried out in dry
glazing. Greenhouse glass has sharp edges,
and calm weather.
especially if it breaks.
•
Always use working gloves while glazing.
•
Assistants and especially children must be
Greenhouse glass has sharp edges,
warned that broken glass is dangerous. Pick
especially if the glass breaks.
up all broken glass at once and remove it with
•
Assistants and especially children must be
care.
•
warned that broken glass is an element of
We recommend that you wear protective
glasses while fixing the spring wire clips.
danger. Pick up broken glass at once and
•
Any ladders that are used must be placed on a
remove it with care.
level surface.
•
We recommend to use protective glasses
•
It is essential to have an assistant available.
while fixing the spring wire clips.
•
Place the ladder on a level support.
PAGE 12: TOOLS
•
It is essential to have an assistant.
Assembling the greenhouse requires the tools
shown on page 12.
References
PAGE 13: FOUNDATIONS
The column marked
indicates the
No base is included with this product. However, an
page(s) on which the component is used.
original base is available separately. This base is easy
to construct and will guarantee you a stable base for
Page 13:
your greenhouse.
Foundation
If you construct your own base, the specified
The base is not included in this delivery.
measurements must be external measurements.
However, an original base can be bought
If you purchase an original base, you will also require
about 75 litres of concrete and six to eight plastic/
separately. It ensures you a stable and easy to
concrete pipes of about 800mm. These pipes, which
build base.
must be buried at a sufficient depth to ensure that
If you make your own base the measurements
they do not freeze, secure the corner and middle
indicated must be external measurements.
anchors.
If you buy an original base you furthermore
The base must be completely level and square;
need about 75 litres of concrete and 6/8
the latter can be ensured by checking that the two
plastic-/concrete pipes of about 800 mm which
diagonal measurements are equal.
are placed in a non-freezing depth for the
ATTACHMENT TO THE BASE
fastening of the corner and middle anchors.
If you construct your own base, you must drill holes
The base must be 100% level and square; the
(7mm) in the ground frame between all the vertical
latter is ensured by checking that the two
profiles. The greenhouse must then be secured to
diagonal measurements are equal.
the base using screws (A).
If you use an original base, the greenhouse must be
Tools
secured to each vertical bar as shown on drawings
The mounting of the greenhouse requires the
B/C.
tools shown on page 12.
PAGE 14-27: ORDER OF ASSEMBLY
Place the components as shown on the illustration
Page 14-27:
and assemble in the order shown in the pictures. Do
Place the components as shown on the
not tighten the nuts fully until the entire sub-frame
illustration and assemble in the order shown
has been assembled.
in the pictures. Do not tighten the nuts
completely until the front gable construction
has been assembled.
Page 13:
PAGE 18: ROOF
The two automatic openers should be frequently
(Fastening to the base).
adjusted and at least twice a year in response to
When constructing your own base you have
major temperature changes. In winter, it is advisable
to drill holes (7 mm) in the ground frame
to maintain a maximum interval of 40 mm between
between all the vertical frames, the greenhouse
the bottom of the cylinder and the tightening screw.
is then fastened to the base with screws (A).
Using an original base the greenhouse is
PAGE 20-23: DOORS AND WINDOWS
fastened to each vertical bar as shown on
For easier assembly, we recommend that you oil the
drawing B/C.
screws for the doors. The glass or polycarbonate for
the door(s) and windows must be fitted at the same
time as the profiles.
Page 24-27:
SIDE 25: DOWNPIPE AND FITTINGS
For an easier assembly we recommend that you
oil the screws for the doors.
PAGES 26-27: FITTING OF GLASS
Important before assembly!
Fitting of glass/polycarbonate
Make sure that the gables and sides are level
Important before glazing!
and square and that door(s) and window(s) are
functioning perfectly.
Make sure that gables and sides are level and
The best order of assembly for the glass:
square, and that door(s) and window(s) are
Windows - Roof - Doors - Gables - Sides
functioning perfectly.
Glass installation (illustrations 1 to 8)
Best order of assembly:
Degrease the sheets and frames with spirit.
1) Windows – 2) Roof – 3) Doors – 4) Gables
Start glazing from the bottom, one pane at a time.
– 5) Sides
Apply a 3mm silicone bead around the vertical
frames as indicated (the dotted lines on the
illustration). (A 3mm bead of silicone is sufficient to
Page 30-33:
ensure maximum adhesion). If you use more silicone
Glazing (illustration 1 to 8)
than recommended, extra tubes can be purchased.
Degrease the sheets and frames with spirit.
Start glazing from below, one glass at a time.
If you accidentally break a pane, carefully pull the
Apply a 3 mm silicone line on the vertical
broken glass outwards and loosen the silicone using
frames where indicated (dotted lines on
a sharp craft knife.
the illustration). (A 3 mm line of silicone is
Clean the profile completely before inserting a new
sufficient to obtain maximum attachment). If
pane of glass.
you do use more than recommended, you can
M-strips are fitted as shown on pages 26. Place the
buy extra tubes.
upper part of the strip under the aluminium profile
along the full length of the sheet and then click the
Spring wire clips and glassholders are to be
strip into position from above.
fitted as shown.
X = Spring wire clips, > = Glassholders
Your greenhouse is now fully assembled. However,
please note the following:
In case of broken glass carefully pull it
MAINTENANCE
outwards and loosen the silicone by means of a
•
Grease the doors (hinges and locks).
sharp craft knife.
•
Keep the gutters free from leaves, etc.
Clean the profile completely before inserting a
•
Adjust the windows as necessary.
new pane of glass.
•
Replace any broken glass.
•
Clean the greenhouse with disinfectant before
Page 34-37:
and after the growing season.
Mounting of polycarbonate
The illustrations at the bottom of page 34/36
WINTER PROTECTION
If you anticipate snow during the winter, we
show where to mount the polycarbonate plates
recommend the following winter precautions:
and lists. The type indication states the length
•
Support the apex of the roof in the middle.
in mm. A possible adjustment is made by
•
Remove any deep snow from the roof.
means of a fine-tooth saw.
•
Take precautions to prevent snow falling from
NB! To avoid the formation of algae the
a tree or roof, for example.
polycarbonate sheets must not come into
•
Remove the cylinders for the automatic
contact with the ground. Rest them on a piece
window openers, if fitted (optional extras).
of cardboard.
•
Adjust the cylinders for the opening of the
hood.
•
Secure the door(s) and window(s) to prevent
A-lists are mounted as shown on page 35/37.
wind damage to the greenhouse.
Put the sheet into the bottom list, bend the
sheet slightly outwards and put it in the top list.
WATER AND CONDENSATION
Please note that your greenhouse is not like a
M-lists are mounted as shown on page 35/37.
conservatory, for example, and that you should
Place the upper part of the list under the alu.
therefore be aware that the greenhouse may leak
profile in the whole length of the sheet and
during or after precipitation and that condensation
will occur on the inside of the greenhouse. Good
hereafter click on the list from above.
ventilation will help prevent condensation.
B
INSURANCE
Sealing of the polycarbonate sheets
Please note that not all insurance companies cover
The sheets may be sealed against insects.
greenhouses automatically. Please contact your
Close the top end off with alu-tape or silicone.
insurance company to ensure that your greenhouse
The bottom only with airstrip tape to let
is covered.
condensation out (available at your local
dealer).
GUARANTEE
Juliana greenhouses are covered by a 12-year
guarantee, which covers the replacement or repair
Now your greenhouse is completely assembled.
of faulty parts. The guarantee does not cover
However, please notice the following:
polycarbonate, glass, transport, assembly, freight,
etc.
Maintenance
Juliana greenhouses are covered by a two-year
•
Grease doors (hinges and lock).
warranty on painted parts, where fitted. Note that
•
Clean the gutter for leaves, etc.
marks on the paint may occur due to suspension of
•
Adjustment of windows.
the profiles.
•
Replacement of broken glass.
The guarantee will be void if the greenhouse is not
assembled in accordance with these instructions.
•
Clean the house with disinfectant before
and after the growing season.
COMPLAINTS
All our greenhouses are built to the highest quality
Winter Protection
standards. However, should you experience any
In areas with occurrence of snow we
problems, please contact your dealer at once. When
recommend the following winter protection:
describing the defect, please state the greenhouse
•
Support the roof ridge at the centre of the
model, the component number and the quality
house.
control number.
•
Remove greater snow loads from the roof.
Any suspension marks or shiny ends on painted
•
Take precautions against snow falling
Juliana profiles will not be visible after the
down from for instance a tree or a roof.
greenhouse has been assembled.
•
Dismount the cylinders for the automatic
window openers, if any (optional extras).
Congratulations on your new greenhouse, which we
•
Secure door(s) and window(s) preventing
hope will bring you a lot of pleasure for many years
wind damage to the house.
to come.
Yours sincerely,
Insurance
Please note that not all insurance companies
Juliana Drivhuse A/S
cover glasshouses automatically. Please
contact your insurance company to ensure an
insurance coverage.
Guarantee
Juliana grants a guarantee of 12 years which
covers replacement of faulty parts. The
guarantee does not cover polycarbonate, glass,
transport, assembly, freight etc.
Juliana grants a guarantee of 2 years on painted
parts, if any. Note that marks in the painting
may occur due to suspension of the profiles.
The guarantee is invalid if the greenhouse is
not assembled according to these instructions.
Complaints
All our greenhouses are built to high standards
of quality. However, should a complaint
occur please contact your dealer at once.
Remember to specify the defect by indicating
the greenhouse model and number of the
component and the quality control number.
USA
Publicité
