Publicité
Transmitter Setup Table (BNF)
DX6e, DX6, DX7, DX8, DX9, DX18, DXs, iX12, iX20, NX6, NX8, NX10
SYSTEM SETUP
Model Type
HELI
Swash Type
Normal
F-Mode Setup
Switch 1
Switch B
Switch 2
Inhibit
Hold Switch
Switch H
0
Channel Assign
Channel Input Config
1 Throttle
2 Aileron
3 Elevator
4 Rudder
5 Gear
F-Mode
6 Collective
7 AUX 2
Frame Rate
11ms
DSMX
ESC Telemetry
Gear Ratio
Motor Pole Count
Panic Mode Operation
Bind / I Button
Pressed = Panic Mode On
Released = Panic Mode Off
LED Indicator on Flight Controller
LED Indicator on FC
Yellow Flash (during calibration)
Red Flash (during calibration)
Smart Throttle (BNF Only)
The new line of Spektrum ESCs feature a telemetry function called Smart Throttle.
Smart Throttle technology combines the throttle signal with telemetry data from
the ESC on one normal three wire servo connector.
Smart Throttle ESCs can send current, voltage, ESC temp, and mAh consumed.
They can also pass along battery data from compatible Spektrum Smart batter-
ies. Smart Throttle telemetry data shows up on your transmitter like any other
telemetry sensor.
For Smart Throttle to function you must have a Smart Throttle ESC paired with a
Smart Throttle telemetry receiver, and a Spektrum DSMX transmitter with telem-
etry. Only certain Spektrum products include Smart technology compatibility, check
your receiver and ESC manual for more information. An update for your transmitter
may be required for Smart features.
(See www.spektrumrc.com to register and update your transmitter.)
To activate Smart Telemetry:
1. Keep the vehicle powered on after binding the transmitter to the receiver.
2. Scroll to the Telemetry screen.
3. Scroll to Settings.
4. Select Auto Config.
FUNCTION LIST
Servo Setup
Chan
THR
AIL
ELE
RUD
GER
1
D/R & Expo
Chan
Sw (F) Pos
0
AILE
1
2
0
ELEV
1
2
0
RUDD
1
2
Gyro
Timer
13.5
Mode
6
Time
Start
Over
One Time
Slow Green Flash
Slow Red Flash
Slow Cyan Flash
www.modellmarkt24.ch
Travel
Reverse
100/100
Normal
100/100
Normal
100/100
Normal
100/100
Normal
100/100
Normal
Throttle Curve
D/R
Expo
100/100
+25
100/100
+25
75/75
+25
100/100
+25
Pitch Curve
100/100
+25
75/75
+25
100/100
+25
100/100
+25
75/75
+25
Mixing
Inhibit
Count Down
5:00
Throttle Out
25%
Inhibit
Indicator Description
Ready to Fly
Failsafe Active
Forward Programming Mode
Calibration proceeding normally
Calibration Error, FC not level or is being moved during calibration
To activate rotor speed infomation using Smart Telemetry:
5. After doing the initial Smart telemetry configuration,
keep the vehicle powered on.
6. Scroll to the Telemetry screen.
7. Scroll to Smart ESC and double select.
8. Scroll down to NEXT.
9. Enter the values for the magnetic pole count of the motor and the gear ratio.
When the radio is on and connected to a receiver sending Smart Data, the Smart
Logo will appear under the battery logo on the home page and a signal bar will
appear in the top left corner of the screen. Scrolling down, past the servo monitor,
the Smart screens will appear. Select either ESC, battery, or both for display to suit
your preference.
5
Chan
Travel
PIT
100/100
AX2
100/100
AX3
100/100
AX4
100/100
Sw (B) Pos
Pt 1
Pt 2
N
0
65
1
80
80
2
100
100
Sw (B) Pos
Pt 1
Pt 2
N
30
40
1
0
25
2
0
25
HOLD
25
37
Normal
Channels
Rate
P-Mix 1
Offset
Switch
Position
Reverse
Normal
Normal
Normal
Normal
Pt 3
Pt 4
Pt 5
65
65
65
80
80
80
100
100
100
Pt 3
Pt 4
Pt 5
50
75
100
50
75
100
50
75
100
50
75
100
-I- > Ger
0/–125
100
Switch I
0
1
EN
Publicité
