Publicité
Page 5 of 8
SV650 & SV650X INSTALLATION:
Undo and remove the engine bolt nut in position arrowed in picture 4 (using 14mm and 17mm
•
sockets), then remove the original engine bolt.
Fit one of the nyloc nuts to new engine bar until nylon engages onto thread (best to use
•
shortest thread end until the thread protrudes by approx. 2mm.
Place plain washer then serrated washer onto bar against nut.
•
Place either bobbin onto bar against serrated washer (so nut and washers fit into counter bore).
•
Place either spacer onto bar against flat face of bobbin.
•
•
Offer this assembly through either frame panel and through original engine bolt hole, push
whole assembly through until spacer goes against the engine bolt mounting face.
On opposite side of bike place spacer over protruding end of engine bar.
•
Place remaining bobbin onto bar against spacer.
•
Place serrated washer then the plain washer onto bar and into bobbin counter bore.
•
Fit nyloc nut and hand tighten.
•
•
Using two 19mm sockets and torque wrench tighten until you feel some compression from
inside the protector. PLEASE NOTE: BOBBIN MUST BE POSITIONED AS PICTURED ON
FIRST PAGE WITH BIGGER END TOWARD FRONT OF BIKE. Do not overtighten as damage
can occur. Do not exceed 40nm of torque.
Fit both bobbin caps into bobbins.
•
Please note: Torque of the engine/bobbin bolts should be checked at regular intervals when doing
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and
suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and
care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that
the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its
option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or
used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the
defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death
and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts
paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns
of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to
faulty goods.
NOTICE DE MONTAGE CP0255BL PROTECTIONS CRASH
L
A PRESENTATION DES PIECES
Merci de noter que dans le cas où les protections sont assemblées avec une bague en caoutchouc, merci de bien vouloir le
retirer lors du montage des pièces sur la moto.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
routine maintenance/servicing.
ISSUE 3 - 03/09/2024 (MH)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
SUZUKI GLADIUS 2009- SV650 2016-/SV650X 2018-
R&G
'
DANS L
EMBALLAGE N
'
EST PAS TOUJOURS IDENTIQUE AU SENS DE MONTAGE
R&G Racing
www.rg-racing.com
CP0255
.
Email:
info@rg-racing.com
Publicité
