Publicité
Les langues disponibles
Les langues disponibles
Table des Matières
FITTING INSTRUCTIONS FOR CP0275 AERO CRASH PROTECTORS
PICTURE ONE
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of
T
HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY
CRASH-PROTECTOR
(B0061/CS340) (x1)
PROTECTOR CAP
(BC0002) (x1)
M12 NYLOC NUT (x1)
M12 PLAIN
WASHER (x1)
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
HONDA CBF1000 2011
mounting to the bike
(
FOR CLARITY OF INSTRUCTIONS ONLY
LEFT HAND SIDE
R&G Racing
www.rg-racing.com
PICTURE TWO
S0203 16mm LONG
SPACER (x1)
SB061 SPINDLE
BAR 133mm LONG
(x1)
M12 SHAKE-PROOF
WASHER (LW0001) (x1)
Email:
info@rg-racing.com
)
Publicité
Table des Matières
Manuels Connexes pour R&G CP0275
Sommaire des Matières pour R&G CP0275
- Page 1 FITTING INSTRUCTIONS FOR CP0275 AERO CRASH PROTECTORS HONDA CBF1000 2011 PICTURE ONE PICTURE TWO THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. Please note that the way the kit is packed does not necessarily represent the way of...
-
Page 2: Right Hand Side
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. CRASH-PROTECTOR (B0061/CS340) (x1) PROTECTOR CAP (BC0002) (x1) SB060 SPINDLE BAR 113mm LONG (x1) M12 SHAKE-PROOF WASHER (LW0001) (x1) M12 NYLOC NUT (x1) M12 PLAIN WASHER (x1) RIGHT HAND SIDE... - Page 3 Left-hand side (as you sit on bike) Remove engine bolt in position arrowed in picture ONE (ensure frame to engine spacer remains in place). Using the spanner flats on the longest spindle bar (SB061) engage the spindle bar by approximately 65mm.
- Page 4 R&G RACING RETURNS POLICY (NON-FAULTY GOODS) Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re- sellable condition, in the opinion of R&G Racing.
-
Page 5: Outils Necessaires
FRANCE INSTRUCTIONS DE MONTAGE DES PROTECTIONS CP0275 AERO HONDA CBF1000 2011 ’ ’ R&G A PRESENTATION DES PIECES DANS L EMBALLAGE N EST PAS TOUJOURS IDENTIQUE AU SENS DE MONTAGE Merci de noter que dans le cas où les protections sont assemblées avec une bague en caoutchouc, merci de bien vouloir le retirer lors du montage des pièces sur la moto, Ne pas commencer le... - Page 6 Côté Droit (assis sur la moto) Enlevez la vis de fixation moteur montrée en photo 2 (picture two), assurez vous que l’entretoise de moteur située entre le moteur et le cadre restent en position. A l’aide de la clef plate de 10 mm, vissez l’axe R&G restant dans la fixation moteur. (engager 65 mm environ) ...