Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. CP0255
  6. Manuel d'instructions

R&G CP0255 Manuel D'instructions

Masquer les pouces
1
2
3
4
5
6
7
8

Publicité

Liens rapides

Télécharger ce manuel
Page 1 of 8
CP0255
FITTING INSTRUCTIONS CP0255 AERO CRASH PROTECTORS
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

loading

Manuels Connexes pour R&G CP0255

Sommaire des Matières pour R&G CP0255

  • Page 1 Page 1 of 8 CP0255 FITTING INSTRUCTIONS CP0255 AERO CRASH PROTECTORS HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
  • Page 2 Page 2 of 8 CP0255 TOOLS REQUIRED GENERAL TORQUE SETTINGS 14mm, 17mm & 19mm A/F SOCKET & WRENCH M4 BOLT = 8Nm • M5 BOLT = • TORQUE WRENCH (UP TO 50Nm) M6 BOLT = SUITABLE SUPPORT JACK • M8 BOLT = 20Nm...
  • Page 3 Page 3 of 8 CP0255 LHS & RHS EXPLODED ASSEMBLY VIEW FITTING PICTURES Picture 1 Picture 2 Picture 3 Picture 4 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
  • Page 4 Page 4 of 8 CP0255 FITTING INSTRUCTIONS Before removing engine bolts, ensure the bike is upright and supported by a suitable engine stand or jack placed under the sump of the motorbike to support the partial weight of the engine, this will prevent the engine from moving during fitting. DO NOT REMOVE MORE THAN 1 ENGINE BOLT AT ANY TIME.
  • Page 5 Page 5 of 8 CP0255 SV650 & SV650X INSTALLATION: Undo and remove the engine bolt nut in position arrowed in picture 4 (using 14mm and 17mm • sockets), then remove the original engine bolt. Fit one of the nyloc nuts to new engine bar until nylon engages onto thread (best to use •...
  • Page 6 Page 6 of 8 CP0255 Outils nécessaires. Jeu de clés Allen incluant la clé de 4 mm. Clés à pipe ou douille /cliquet de 14 – 17 et 2x 19 mm. Scie cloche de 28 mm. (non requis pour SV650 2016- ou SV650X 2018).
  • Page 7 Page 7 of 8 CP0255 • Démonter le cache droit et à l’aide d’un foret dia 5-6 mm ou du foret centreur de la scie cloche de 28 mm, percer le centre du marquage (percer de l’intérieur vers l’extérieur). Remonter le cache sur la moto et vérifier que le perçage est dans l’alignement de l’outil pointu et de l’axe de fixation •...
  • Page 8 Page 8 of 8 CP0255 • Placez la rondelle dentelée sur l’axe et dans l'alésage de la bobine. Placez la rondelle plate sur l’axe contre la rondelle dentée. • Monter l'écrou puis serrez le à la main. • • A l’aide de 2 clés à cliquet + douille 19mm et d’une clé dynamométrique, serrer jusqu’à ce que la compression s’accentue à...