Publicité
• Note the direction of rotation of the motor and saw
blade. Use only blades whose permissible maxi-
mum speed is not lower than the maximum spindle
speed of the circular saw and of the material to
be cut.
• After you have switched off the motor, never slow
down the saw blade by applying pressure to its
side.
• Only fit blades which are well sharpened and have
no cracks or deformations.
• Only use saw blades that are recommended by the
manufacturer, comply with EN 847-1.
• Faulty saw blades must be replaced immediately.
• Never use saw blades which do not comply with
the data specified in this manual.
• Never dismantle the machines safety devices or
render them inoperative.
• If the table insert is worn, replace it.
• Always stand to the side of the saw blade when
working with the saw.
• Never load the machine so much that it cuts out.
• Make sure that off-cuts do not catch on the saw
blade crown.
• Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
• To rectify faults or remove jammed pieces of wood,
always switch off the machine first. - Unplug the
power plug -
• If the sawing gap is worn, replace the table insert.
Turn off the machine and unplug the power plug.
• Carry out retooling work, adjustments, measure-
ments and cleaning jobs only when the motor is
switched off. - Unplug the power plug -
• Before switching on, make sure that all keys and
wrenches have been removed from the tool.
• Switch off the motor and unplug the power plug
before you leave the workplace
• Refit all guards and safety devices immediately
after you have completed any repairs or mainte-
nance work.
• Be sure to observe the safety information and op-
erating and maintenance instructions issued by the
manufacturer, as well as the dimensions listed in
the Technical Data.
• It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
• Make sure you stand squarely and keep your bal-
ance at all times.
• Check the tool for damage!
• Each time before re-using the tool, carefully check
that the guards or any slightly damaged parts are
working as intended.
• Check that the moving parts are in good working
order, that they do not jam, and that no parts are
damaged. Make sure that all parts are fitted cor-
rectly and that all other operating conditions are
properly fulfilled.
18
GB
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
• Unless otherwise stated in the operating instruc-
tions, damaged safety devices and parts must be re-
paired or replaced by an authorized service center.
• This tool conforms to the applicable safety regula-
tions. Repairs may only be performed by a special-
ist using original spare parts. Otherwise accidents
could occur.
• If necessary, wear suitable personal protection
equipment. This could consist of:
- Ear plugs to prevent the risk of damaging your
hearing;
- A breathing mask to avoid the risk of inhaling
hazardous dust.
- Always wear gloves when handling saw blades
and rough materials. Whenever practicable, saw
blades must be carried in a container.
• The operator must be informed about the condi-
tions that influence the generation of noise (for
example saw blades designed to reduce noise
emissions, caring for blades and the machine).
• Faults on the machine or its guards, safety devices
and blade must be reported to the person in charge
as soon as they are discovered.
• Use only the transport devices to move the ma-
chine. Never use the guards for handling and mov-
ing the machine.
• All operators must receive proper training in the
use, adjustment and operation of the machine.
• Do not saw any materials that contain foreign bod-
ies such as wires, cables or ties.
• Only use sharp saw blades.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair active
or passive medical implants under certain conditions.
In order to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.
3. Use only as authorized
The firewood circular saw is designed exclusively
with the offered tool for the processing of wood.
The machine corresponds to the valid EC guide-
line.
• The log saw is constructed as 1-man-operating
stand and is only to be used in outdoor locations.
• The log saw is a portable circular saw. It is only ap-
plicable to cross cut firewood with a feeding rocker
according to the technical specifications.
• The saw is constructed solely for cross cutting of
firewood with max. 1 meter length.
• Regardless of the diameter of the wood only 1
work piece is to be put on the rocker.
• Observe all safety and hazard notes on the ma-
chine and ensure they are kept complete and in a
legible condition.
• Observe all safety and hazard notes on the ma-
chine and ensure they are kept complete and in a
legible condition.
Publicité
