Siemens SPCN110 Mode D'emploi page 2

English
WARNING
This device shall only be connected to power
supplies compliant to EN60950-1, chapter 2.5
("limited power source").
EC Declaration of Conformity
Siemens Security Products hereby declares that
this product is in compliance with the essential
requirements and other relevant provisions of
Directive 2004/108/EC on Electromagnetic
Compatibility (EMC).
The EC Declaration of Conformity is available from
your Siemens sales office or:
Siemens AB, Security Products
Englundavägen 7
SE-171 24 Solna
Sweden
Introduction to the SPCN110
The SPCN110 provides the SPC controller with a
standard analogue line interface for enhanced
communications and connectivity. The unit
connects to the controller board via a 16 pin
connector and is secured by 2 mounting pillars. The
SPCN110 provides a 4 pin terminal block to
connect the PSTN line and 4 status LED's to
provide a visual indication of the current status.
See Fig.1: Top of module (left) and underside
(right)
Mounting pillar holes (x2)
1.
The SPCN110 contains 2 mounting pillar holes
which allow the mounting pillars to be inserted for
securing the board to the PCB. For further
information see section - Installing the SPCN110.
PSTN Line Terminal Block
2.
The terminal block for the PSTN line consists of 4
screw terminals (A, B, C, D). The PSTN line
connects to the AB terminals. A PSTN telephone
may be connected to the CD terminals.
Status LED's
3.
The 4 SPCN110 status LED's indicate the
following conditions:
ON – Line fault detected
LED 1
OFF – No line fault detected.
ON – Carrier signal detected
LED 2
OFF – No carrier signal detected.
LED 3 ON if the modem is off-hook
OFF if the modem is on-hook.
LED 4 Flashing (1 second ON/OFF) indicates
that the PSTN module hardware is
functioning correctly.
Controller interface terminal block
4.
The interface to the SPC controller is comprised
of a dual in-line socket for mounting onto the 16
pin header on the PCB. This interfaced is keyed
to ensure the SPCN110 is inserted onto the
board in the correct orientation.
Installing the SPCN110
WARNING
Do not install a SPCN110 on a powered
controller.
When installing plug-in modules on the SPC
controller PCB always ensure that the
primary modem (left slot) is installed before
installing a back-up module (right slot). A
single modem installed in the right slot will
not function as a primary modem.
The backup module (right slot) on the SPC
controller uses the same communication
channel as serial port 2. Please ensure that
no devices are connected to serial port 2
when the backup modem is installed.
See Fig. 2: Mounting pillars
See Fig. 3: PCB with mounting pillars
1 SPCN110 with mounting pillars inserted
2 PCB Mounting pillar holes
Installation Instruction
See Fig. 4: Correctly installed SPCN110
The SPCN110 is supplied with 2 x mounting pillars
(see Fig.2) for securing the module to the controller
PCB. To install the module onto the controller
adhere to the following steps:
Power down the controller (disconnect the

battery leads from the battery if one is
connected).
Insert one end of each of the two mounting

pillars into the holes provided at the top of the
SPCN110. (The two holes on either side of the
PSTN line connector block). Push firmly until
each is secured in place.
Align the interface terminal block of the

SPCN110 (with pillars inserted) over the SPC
controller interface terminal on the PCB (see Fig.
3).
Slowly but firmly push the module down onto

the PCB until both mounting pillars are secured
to the PCB and the interface terminal block is
connected.
Check that the module appears correctly

connected (see Fig. 4) and then power-up the
controller again. LED 4 on the PSTN module will
flash regularly (once every 2 seconds approx.) to
indicate that the PSTN module hardware is
functioning correctly.
Configuring the SPCN110
For configuration instruction please refer to SPC
Configuration Manual.
Technical Data
Network PSTN (analogue telephone
connection network)
Quiescent Max. 35 mA at 12 VDC
current (communication active)
Operating
Max. 25 mA at 12 VDC
Current
Operating
-10 ~ +50 °C
temperature
Relative Max. 90 % (non condensing)
humidity
Plug on module to SPC
Mounting
controller
Dimensions
90 x 38 x 25 (PCB)
(W x H x D)
Weight 0.030 kg
IP Rating IP30
Standards / EN50131-1 approved with
Approval control panel