Burda BRELD2200 Notice D'utilisation Et D'entretien page 9

meters above the ground. The minimum
installation height for bathrooms is 2.25 m above
the ground.
• A safety distance of not less than 100 cm should
always be left in front of the heater.
• Since the device emits radiant heat, make sure that
no items such as furniture are located between the
device and the persons or objects to be warmed!
• The distance between the heater and combustible
objects as well as other structures must be at least
100 cm. The distance to the ceiling must be at least
30 cm and laterally to the wall 50 cm.
P :
OWER CORD
• The use of an extension cord with this appliance is
not recommended.
• The power cord must not come into contact with
heated parts of the device!
• Children aged from 3 years and less than 8 years
shall not plug in, regulate and clean the appliance
or perform user maintenance.
• Never remove the plug from the socket by pulling
on the cord! Never move the device by pulling on the
cord or carry the device by the cord!
• Do not wind the cord around the device! Do not
operate the device with the cord wound up!
• Do not clamp the cord, or pull it over sharp edges!
• Do not run cord under carpeting, throw rugs or
runners etc. Arrange cord away from areas where it is
likely to be tripped over.
•Never use the appliance if the appliance or cord is
damaged. Risk of injury!
• The energy supply to the heater must always be
properly earthed.
• The appliance must not be located neither directly
below, nor in front of a socket-outlet.
• The heater must be installed so as to prevent that
the switches can be touched from those who are in
the shower.
• If the appliance is not used for a long period,
disconnect it from the power supply.
I :
NSTALLATION
• The installation should always be carried out by a
qualified electrician or a competent person in
accordance with the current electrical standards for
your country:
(ex. HD 384 CENELEC for Mainland Europe, IEC 60446
and BS7671 for the United Kingdom, IEC 60445(2010)
& ET101:2008 for Ireland and IEC 60364-7 1988
Internationally, AS/NZS 3000 for Australia) and
according to the UE 2015/1188 standards. Risk of fire!
• Only commission the device after it has been
fully installed.
All manuals and user guides at all-guides.com
• This heater comes with a pair of stainless steel
adjustable angle mounting brackets. The adjustable
angle enables the heater to be installed on horizontal
and inclined surfaces.
I :
NSTALLATION
In case of direct connection to the supply line, a
bipolar switch or a bipolar circuit breaker with contact
opening distance of at least 3mm must be fitted
upstream from the supply line. Contact an authorized
service technician if you are unsure if you have a
switch or a circuit breaker installed on the premises.
Plug in the device in the socket of main power, the
heater starts heating.
Unplug the device from the socket or press the
switch or the circuit break to power off the device.
After switching on the appliance for the first time
and following extended periods on non-use, the
appliance may expel a slight odor for a short time.
It will not affect the use of the heater.
To exclude unpleasant burnt odor, it is
recommended to keep the heater clean preventing
accumulation of dust on it.
C :
LEANING
• First, disconnect the equipment from the power
supply system!
• After the appliance has cooled down, wipe off dust
with a damp soft rag.
• During operation, it is necessary to periodically
(once a year) check the electric cable contacts and
terminal connectors for good tightening.
• Make sure all parts are dry before using again.
• Do not use any abrasive or caustic cleaning agents!
• Never immerse the appliance in water! Danger to
life!
A -S S :
FTER ALES ERVICE
• All repairs must be referred to authorised
personnel! Therefore, you should contact your
specialized dealer or the customer service.
• Important! Any tampering with the appliance will
invalidate the warranty.
• Repairs carried out improperly and by unqualified
persons may have serious consequences for the user!
T D :
ECHNICAL ATA
• Connection/fuse: 230/240 Volt (50/60 Hz) 16 Amp
• Output: 2200 Watt = BRELD2200-3 und 2400 Watt =
BRELD2200-1
• Guaranteed service life: up to 5000 hours with
average use
• Type of protection: IP55
• Weight: 7.8 kg
• Casing: Corrosion-resistance anodized aluminium
• Cable: 1.90m 3-wire 1.5 mm², Schuko plug.
GB