Publicité
Les langues disponibles
Les langues disponibles
Installation / Operation
handle faces to the back through the rear
opening on the fitting. Then screw it to the han-
dle (see Fig. C3).
Position the fitting
hole (see Fig. C4).
Below the washbasin first place the C sealing
washer
, then the C metal washer
6
the two thread bolts
Now screw the securing nuts
bolts
and tighten with a spanner SW 10 mm
8
until the fitting
is firmly seated on the
1
washbasin (see Fig. C4).
Unscrew the upper pop-up flange
lower pop-up flange
From the top insert the upper pop-up flange
with the upper pop-up seal
basin drain hole.
Place the lower pop-up flange
pop-up seal
beneath the washbasin drain
16
hole.
Now screw together the lower pop-up flange
and the upper pop-up flange
17
pop-up plastic nut
Fig. C5).
Unscrew the pop-up plastic nut
lower pop-up flange
side the female thread of the lower pop-up
flange
.
17
ATTENTION! DANGER OF INJURY, SHEET
METAL HAS SHARP EDGES.
Temporarily remove the clip and pop-up joint
from the pop-up pivot rod
Be sure the seal remains on the pop-up pivot
rod
.
12
Place the pop-up plastic nut
piece of the pop-up pivot rod
seal is placed between the ball and pop-up
plastic nut
.
19
Inset the short section of the pop-up pivot rod
into the female thread of the lower pop-up
12
flange
and retighten the pop-up plastic nut
17
hand tight.
19
Reattach the clip and pop-up joint
pop-up pivot rod
12
16 GB/IE
over the washbasin tap
1
over
7
(see Fig. C4).
8
onto the thread
9
from the
15
.
17
into the wash-
14
with the lower
17
so the
15
faces to the back (see
19
from the
19
, leaving the seal in-
17
for installation.
12
over the longer
19
. Be sure the
12
to the
11
.
Insert the pup-up pull rod
tic section of the pop-up joint
the screw using a cross-tip screwdriver.
Verify the pop-up is working properly. The plas-
tic screw below the pop-up drain plug
need to be adjusted. Then retighten with the
lock nut.
Install the siphon by screwing together the
siphon and the pop-up screw thread
Check the seals inside the swivel nuts
the flexible connection hoses
Screw the flexible connection hoses
angle valves. Be sure to correctly install the
flexible connection hoses
water hoses – left flexible connection hose
15
to the hot water connection, left angle valve,
and the right flexible connection hose
the cold water connection, right angle valve
(refer to Fig. C5).
Operation
Start-up
After the initial commissioning, carefully check all
connections for leaks.
Check the operation of the fitting. To do so,
swing the handle
tions.
11
Note: the fitting
is lit through an integrated turbine (without batteries).
The LED colour changes automatically based on the
water temperature through an integrated tempera-
ture sensor:
·
up to approx. 33°C blue,
·
from approx. 33-39°C green,
·
over approx. 39°C red,
·
over approx. 53°C flashing red
Open the main water supply.
Lift the handle
left in order to regulate the speed or tempera-
ture of the water.
through the plas-
5
and tighten
11
18
.
10
10
to the cold- / hot
10
into all permissible posi-
23
features an LED light. The LED
1
and swing it to the right or
23
may
13
.
on
20
to the
10
to
10
Publicité
