MIRKA ROS 350NV Mode D'emploi page 31

77 mm )3 in.( 12,000 rpm Random Orbital Sanders )see "Product Configuration/Specifications" table for
particular model) to which this declaration relates are in conformity with the following standard(s) or other normative document(s):
EN ISO 12100:2010, EN ISO 11148-8:2011, EN ISO 15744:2008 & EN 28927-3:2009 in accordance with the regulation 2006/42/EC.
Jeppo 23.06.2020
Place and date of issue
Operator Instructions
Includes – Please Read and Comply, Proper Use of Tool,
Work Stations, Putting the Tool Into Service, Operating Instruc-
tions, Product Configuration/Specifications Tables, Parts Page,
Parts List, Sander Spare Parts Kits, Troubleshooting Guide.
Manufacturer/Supplier
Mirka Ltd.
FI-66850 Jeppo, Finland
Tel: + 358 20 760 2111
WARNING
Always wear required personal safety protection in accordance with manufacturer's instructions and local/national standards while
using this tool.
• Do not use a power tool if you are tired or under the influence of drugs, alcohol or medication.
• Read the Materials Safety Data Sheet )MSDS( for the working surface.
• Use the tool with dust extraction. A suitable dust extraction unit will reduce hazardous dust.
• Do not overreach. Keep proper footing and balance at all times.
• Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
• If any physical hand/wrist discomfort is experienced, stop working and seek medical attention.
Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibrations.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
• The tool is not electrically insulated. Check work area for live electricity, gas pipes, etc. before operation.
CAUTION
• Prevent unintentional starting.
• Remove pad wrench before connecting the tool to the air supply.
• Keep work area clean and well lit.
• Always ensure that the work piece to be sanded is firmly fixed.
• Before changing abrasive always disconnect the air supply.
Additional safety warnings
• Read all instructions before using this tool. All operators must be fully trained in usage and safety of this tool.
• All maintenance must be carried out by trained personnel. For service, contact Mirka authorized service centre!
• Always wear required safety equipment )see warnings(.
• The operator must be in a secure position and have a firm grip and footing on a solid floor.
• Always ensure that the work piece to be sanded is firmly fixed.
• Check tool, backing pad, hose and fittings regularly for wear.
• Always take care to ensure your safety at work; never carry, store or leave the tool unattended with the air supply connected.
• Vacuum unit dust collection bag should be cleaned or replaced daily. Dust can be highly combustible.
Cleaning or replacing of bag also assures optimum performance.
• Do not exceed maximum recommended air pressure of 6.2 bar )90 psi(.
• Take care to avoid entanglement of the moving parts of the tool with clothing, ties, hair, cleaning rags, etc.
• Keep hands clear of the spinning pad during use.
• If the tool appears to malfunction, remove from use immediately and arrange for service and repair.
• Before changing abrasive always disconnect the air supply. Take care to properly attach and centre the abrasive
on the backing pad.
Declaration of conformity
Mirka Ltd.
FI-66850 Jeppo, Finland
declare on our sole responsibility that the products
Company
Important
Read these instructions care-
fully before installing, operating,
servicing or repairing this tool.
Keep these instructions in a safe
accessible location.
28
Mirka 12,000 rpm
77 mm (3 in.) LIGHTWEIGHT
RANDOM ORBITAL SANDERS
Stefan Sjöberg, CEO
Required Personal Safety Equipment
Safety Glasses Breathing Masks
Safety Gloves Ear Protection
Original Instructions