Stihl HSA 130.0 R Notice D'emploi page 34

English
Fault LEDs on the
battery
18 Specifications
18.1 STIHL HSA 130.0 R,
HSA 130.0 T Hedge Trimmer
– Permitted batteries:
– STIHL AR
– STIHL AP together with "AP belt bag with
connecting cable"
– Weight without battery:
– HSA 130.0 R, blade length 600 mm: 4.1 kg
– HSA 130.0 R, blade length 750 mm: 4.4 kg
– HSA 130.0 T, blade length 600 mm: 3.9 kg
– HSA 130.0 T, blade length 750 mm: 4.1 kg
– Degree of electrical protection: IPX4 (protec‐
tion against splash water from any direction)
The running time is shown at www.stihl.com/
battery-life.
18.2 Cutting blades
HSA 130.0 R
– Tooth spacing: 38 mm
– Cutting length: 600 mm or 750 mm
– Sharpening angle: 45°
HSA 130.0 T
– Tooth spacing: 30 mm
– Cutting length: 600 mm or 750 mm
– Sharpening angle: 45°
18.3 Sound Values and Vibration
Values
The K-value for the sound pressure level is
2 dB(A). The K-value for the sound power level is
2 dB(A). The K-value for vibration level is 2 m/s².
HSA 130.0 R, blade length 600 mm
– Sound pressure level L
fied in EN 62841‑4‑2: 83 dB(A)
– Sound power level L
in EN 62841-4-2: 94 dB(A)
– Vibration level a measured as specified in
hv
EN 62841-4-2
– Control handle: 3.5 m/s²
– Loop handle: 2.7 m/s²
HSA 130.0 R, blade length 750 mm
– Sound pressure level L
fied in EN 62841‑4‑2: 84 dB(A)
34
Cause
The battery service
life has been excee‐
ded.
measured as speci‐
pA
measured as specified
wA
measured as speci‐
pA
Remedy
► Replace battery.
– Sound power level L
in EN 62841-4-2: 95 dB(A)
– Vibration level a measured as specified in
hv
EN 62841-4-2
– Control handle: 3.6 m/s².
– Loop handle: 2.8 m/s²
HSA 130.0 T, blade length 600 mm
– Sound pressure level L
fied in EN 62841‑4‑2: 84 dB(A)
– Sound power level L
ance with 62841-4-2: 95 dB(A)
– Vibration level a measured as specified in
hv
EN 62841-4-2
– Control handle: 3.0 m/s²
– Loop handle: 2.8 m/s²
HSA 130.0 T, blade length 750 mm
– Sound pressure level L
fied in EN 62841‑4‑2: 85 dB(A)
– Sound power level L
in EN 62841-4-2: 96 dB(A)
– Vibration level a measured as specified in
hv
EN 62841-4-2
– Control handle: 2.5 m/s²
– Loop handle: 2.9 m/s²
The vibration levels indicated were measured
according to a standardized test method and can
be used as a basis for comparing electric power
tools. The vibration levels actually occurring may
vary from the values indicated, depending on the
type of application. The vibration levels indicated
can be used for an initial estimate of the vibration
stress. The actual vibration stress has to be esti‐
mated. The times can be taken into account in
the estimate when the electric power tool is
switched off and also when it is switched on but
running without any load.
For information on compliance with Employers'
Vibration Directive 2002/44/EC see
www.stihl.com/vib.
18.4 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
18 Specifications
measured as specified
wA
measured as speci‐
pA
measured in accord‐
wA
measured as speci‐
pA
measured as specified
wA
0458-021-9601-A