DeWalt XR DCS355N Traduction De La Notice D'instructions Originale page 39

Proper Hand Position (Fig. N)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires the tool to be held as shown in
Figure N.
Instructions for Use (Fig. N)
1. Install the battery pack.
2. To turn the tool ON, hold it as shown in Figure N and press
the variable speed trigger
nOTE: The further the trigger switch is depressed the faster
the tool will operate. If in doubt about the proper speed
for your operation, test the performance at low speed and
gradually increase until a comfortable speed is found.
3. To turn the tool OFF, release the variable speed trigger
Lock On/Off Button (Fig. O)
The tool can be locked off by fully depressing the lock on/off
button 4 shown in Figure O.
For more comfort in extended use applications, the lock
on/off button 4 can lock the trigger trigger
depressed position.
nOTE: The tool will automatically shut off after operating
for five minutes with the lock‑on button engaged. To restart
the tool, the user will have to release the trigger and repress
lock‑on button.
Speed Selector (Fig. A)
DCS356
Your tool is equipped with a speed selector
you to select one of the three speeds that limits the full speed.
Select the speed based on the application and control the speed
of the tool using the variable speed trigger switch
LED Worklight (Fig. P)
The LED worklight 2 will activate when the trigger is depressed.
It will automatically shut off following a short period of time
once the trigger is released.
Using the Dust Extraction Adaptor with the
Sanding Platen (Fig. R)
1. Attach the dust extraction adaptor
the Dust Extraction Adaptor.
2. Attach the sanding platen
Installing/Removing Accessories.
3. Attach sanding sheet as described under Installing/
Removing Sanding Sheets.
Using the Dust Extraction Adaptor with
Plunge Cutting Accessory (Fig. S)
1. Attach the dust extraction adaptor. Refer to Attaching the
Dust Extraction Adaptor.
1 .
1 in the
10 which allows
1 .
. Refer to Attaching
17
as described under
23
2. Push dust extraction arm
dust extraction adaptor
3. Attach plunge cutting blade as described under Installing/
Removing Accessories.
4. Adjust the dust extraction arm
Helpful Hints
• Always ensure the workpiece is firmly held or clamped to
prevent movement. Any movement of the material may
affect the quality of the cutting or sanding finish.
• Do not start sanding without having the sandpaper
attached to sanding platen.
• Use coarse grit paper to sand rough surfaces, medium grit
for smooth surfaces and fine grit for the finishing surfaces. If
necessary, first make a test run on scrap material.
• Excessive force will reduce the working efficiency and cause
motor overload. Replacing the accessory regularly will
1 .
maintain optimum working efficiency.
• Do not allow the sandpaper to wear away, it will damage
the sanding pad.
• If the tool overheats, especially when used at low speed,
set the speed to maximum and run it with no load for 2–3
minutes to cool the motor. Avoid prolonged usage at very
low speeds. Always keep the blade sharp.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.

WARNING:To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Electrical shock and mechanical hazard.
Disconnect the electrical appliance from the power source
before cleaning.

WARNING: To ensure safe and efficient operation,
always keep the electrical appliance and the ventilation
slots clean.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Ventilation slots can be cleaned using a dry, soft non‑metallic
brush and/or a suitable vacuum cleaner. Do not use water or
EngLIsh
19 into the lower aperture of the
17 .
19 for best results.
37