DeWalt XR DCS355N Traduction De La Notice D'instructions Originale page 38

EngLIsh
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Installing/Removing Accessories (Fig. C–M,Q)
Tool‑free Accessory clamp (Fig. C–E)
The DCS355, DCS356 features a quick change accessory system.
This allows for faster accessory changes without the need for
wrenches or hex keys like other oscillating tool systems.
1. Grasp the tool and squeeze the accessory clamping lever
as shown in Figure C.
2. Clean any residual debris from the tool shaft and the
accessory holder.
3. Slide the accessory between the shaft
holder making sure the accessory engages all eight pins on
the holder and is flush with the shaft. Ensure the accessory is
oriented as shown in Figure D.
4. Release the accessory clamp lever.
nOTE: Some accessories, such as scrapers and blades can be
mounted at an angle if required as shown in Figure E.
Installing/Removing Sanding Sheets (Fig. F)
A diamond shaped platen uses a hook and loop adhesion
system to attach the sanding sheets. The platen allows you to
use it on large flat surfaces and tight spots or corners.
1. Attach the sanding platen
Installing/Removing Accessories.
2. Align the edges on the sanding sheet, with the edge of
the sanding platen and press the sanding sheet
the platen.
3. Firmly press the base with the sanding sheet attached
against a flat surface and briefly switch the tool on. This
provides for good adhesion between the platen and the
sanding sheet and also helps to prevent premature wear.
4. When the tip of the sanding sheet becomes worn, detach
the sheet from the platen, rotate and reapply.
Attaching Accessories Using the Universal
Adapter (Fig. G)

CAUTION: To avoid injury, do not use any accessory
for an application where the adaptor may fail to hold
the accessory.

CAUTION: Read and follow all manufacturers' safety
warnings for any accessories used with this tool.

CAUTION: To avoid injury, ensure adaptor and accessory
are securely tightened.
Non‑D WALT accessories can be attached using the
e
universal adaptor.
1. Place the washer 20 on the tool.
2. Place accessory 12 on to washer.
3. Tighten and secure adaptor nut
Attaching the Cut Guide (Fig. H–M)
The depth/cut guide allows you to precisely cut material at a
specified depth and more accurately track a marked cut line.
36
and the accessory
22
23 as described under
24 onto
18 using hex wrench
1. Attach the cut guide block
tabs 13 on the guide into the accessory side mount slots
on the main body of the tool.
nOTE: The depth/cut guide can be attached to either side
of the tool.
2. Secure the block to the main body with the supplied
screw 15 and washer
wrench 16 .
Depth guide (Fig. I, J)
This feature allows you to precisely cut material at a
3
specified depth.
1. Insert the guide arm
slot on the guide block
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired cut depth as shown in
Figure J.
3. Secure the guide in place by turning the depth/cut
adjustment knob
the depth/cut adjustment knob counterclockwise.
cut guide (Fig. k–M)
This feature allows you to more accurately track a marked
cut line.
1. Insert the guide arm
on the left and right sides of the guide block
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired length as shown in Figure L.
3. Secure the guide in place by turning the depth/cut
adjustment knob
the depth/cut adjustment knob counterclockwise.
nOTE: The guide arm can also be placed in the guard assembly
vertically in order to set the height off a cut. Refer to Figure M.
Attaching the Dust Extraction Adaptor (Fig. Q)
The Dust Extraction Adaptor allows you to connect the tool to
an external dust extractor, either using the AirLock™ system
(DWV9000‑XJ), or a standard 35 mm dust extractor fitment.
1. Attach the dust extraction adaptor
tabs 13 in to the accessory side mount slots
nOTE: The dust extraction adaptor can be attached to either
side of the tool.
2. Insert screw 15
adaptor 17 and tighten with the supplied hex wrench
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
16 .
start-up can cause injury.

WARNING: Ensure switch is fully OFF before installing
the battery.
6 by inserting the accessory
21 . Tighten with the supplied hex
7 as shown in Figure I into the front
6 .
14 clockwise. To release the guide turn
7 as shown in Figure K into the slots
14 clockwise. To release the guide turn
17 by inserting the
and washer 21 into the dust extraction
5
6 .
5 .
16 .