Specifications; Interface - Sony UP-D2500 Mode D'emploi

Specifications

Printer
Power requirements
220 to 240 V AC, 50/60 Hz
Power consumption
About 1.0 A max. at 25°C, 240 V AC
Operating temperature
5°C to 35°C (41°F to 95°F)
Operating humidity
20 % to 80 % (no condensation allowed)
Storage and transport temperature
–20°C to 60°C (–4°F to 140°F)
Storage and transport humidity
20 % to 90 % (no condensation allowed)
Dimensions
About 370 × 125 × 417 mm (w/h/d)
× 5 ×16
5 3
(14 ⁄
8
Mass About 9.5 kg (20 lb 15 oz)
Printing system
Sublimation heat transfer printing
Picture Memory
2 Mbytes
Picture element
Maximum 1365 × 1024 dots (310 dpi)
For self-laminating color printing:
Maximum 1646 × 1024 dots
Thermal head
12.2 dots/mm (1024 dots)
Total gradation
256 levels each for yellow, magenta, and
cyan
Digital interface
Parallel data interface - 1 channel
Amphenole 36-pin connector × 1
Printing time
Approximately 45 seconds
(for color printing, excluding the data
transmission time)
Protection against electric shock:
Class I
Protection against harmful ingress of water:
Ordinary
Degree of safety in the presence of flammable
anesthetics or oxygen:
Not suitable for use in the presence of
flammable anesthetics or oxygen
Mode of operation:
Continuous
Supplied accessories
Paper tray (1)
AC power cord (1)
Paper cover (1)
Color printing pack (1)
2HD floppy disk
(Windows software) (1)
2HD floppy disk
(Macintosh software) (1)
2HD folppy disk (Printer color table) (1)
Software license agreement (1)
Instructions for Use (1)
a) Contains data for the instruction manual for the
printer driver
Optional accessories
Color printing pack UPC-2010
Self-laminating color printing pack UPC-
2040A
⁄ inches)
4
a)
a)
Self-adhesive color printing pack
UPC-20S01
16-split Self-adhesive Pre-cut color printing
pack UPC-20S16E
4-split Self-adhesive Pre-cut color printing
pack UPC-20S04E
Color Postcard printing pack
UPC-2070E
B/W printing pack UPC-2020
UPA-2001 paper ejector
UPA-2002 paper tray
Interface cable UPZ-2000M

Interface

Control connector
IEEE 1284-B connector (amphenol 36-pin)
Input: Max. 5 V (TTL)
Output: Max. 5 V (TTL)
Data transmission system
8 bit, parallel,
IEEE STD 1284-1994 (Compatible, Reverse
Nibble and ECP modes)
Logic levelTTL
Parallel Interface connector pin assignment
Pin No. I/O Signal
Interface mode
Compatible Nibble
1 I nStrobe HostClk
2 I/O Data1 (LSB)
3 I/O Data2
4 I/O Data3
5 I/O Data4
6 I/O Data5
7 I/O Data6
8 I/O Data7
9 I/O Data8 (MSB)
10 O nACK PtrClk
11 O Busy PtrBusy
12 O PError AckDataReq nAckReverse
13 O Select Xflag
14 I nAutoFd HostBusy
15 Not defined
16–17 GND
18 O Peripheral Logic High (pull up to +5 V at 1 kilohm)
19–30 GND
31 I nInit nInit
32 O nFault nDataAvail
33 Not defined
34 Not defined
35 Not defined
36 I nSelectIn IEEE 1284 Active IEEE 1284 Active
UP-D2500 supports Compatible, Reverse Nibble, and
ECP modes of the two-way parallel interface standard
(IEEE STD 1284-1994).
Design and specifications are subject to change without
notice.
ECP
HostClk
PeriphClk
PeriphAck
Xflag
HostAck
nReverseRequest
nPeriphRequest
23
Others