Maytag Commercial MLE27PDFGW Instructions D'installation page 15

Display
After the dryer has been installed and plugged in, the display
will show "0 minutes."
PD Models
PRICE
1.50
PRICE
1.50
Once the dryer has been plugged in and the dryer door opened
and closed, the display will show the vent price. PN/PR models
are factory preset for free cycles; the display will flash "SELECT
CYCLE."
PR Models
SELECT CYCLE
SELECT CYCLE
Control Set-up Procedures
I
MPORTANT: Read all instructions before operating.
The fabric setting buttons along with the digital display are
used to set up the dryer controls. The display can contain
4 numbers and/or letters and a decimal point. These are used
to indicate the set-up codes and related code values available
for use in programming the dryer.
How to Use the Buttons to Program the Controls
1. The HEAVY DUTY button is used to adjust the values
associated with set-up codes. Pressing the button will
change the value by increments. Rapid adjustment is
possible by holding down the button.
2. The NORMAL button will advance the display through the
set-up codes. Pressing the button will advance the display to
the next available set-up code. Holding down the NORMAL
button will automatically advance through the set-up codes
at a rate faster than 1 per second.
3. The DELICATES button is used to select or deselect options.
PD Models: Insert access panel key and turn
■
counterclockwise.
PR Models: If the card reader is installed (according to the
■
reader manufacturer's instructions), the setup mode can be
entered by inserting a manual setup card (supplied by the
reader manufacturer) into the card slot. The dryer is now in
the setup mode.
If no card reader is installed, insert access panel key and
turn counterclockwise.
NOTE: This dryer is preset at the factory and does not require
any programming. However, if you want to change the settings,
follow the "Setup Codes" guide below.
PD Model units are preset at the factory for fixed cycle price
■
with top off.
PR Model units are preset for free cycle operation so they
■
can be run without readers or coins.
UPPER DRYER UPPER DRYER
HEAVY PERMANENT
WHITES
DELICATES
NORMAL
DELICATES
& COLORS
DUTY PRESS
MEDIUM HEAT LOW HEAT
HIGH HEAT HIGH HEAT MEDIUM HEAT LOW HEAT
HEAVY WHITES PERMANENT
DELICATES
NORMAL
DELICATES
& COLORS PRESS
DUTY
MEDIUM HEAT LOW HEAT
HIGH HEAT HIGH HEAT MEDIUM HEAT LOW HEAT
LOWER DRYER LOWER DRYER
UPPER DRYER UPPER DRYER
WHITES HEAVY PERMANENT
DELICATES
NORMAL
DELICATES
& COLORS PRESS
DUTY
MEDIUM HEAT LOW HEAT
HIGH HEAT HIGH HEAT MEDIUM HEAT LOW HEAT
HEAVY WHITES PERMANENT
DELICATES
NORMAL
DELICATES
& COLORS PRESS
DUTY
MEDIUM HEAT LOW HEAT
MEDIUM HEAT LOW HEAT
HIGH HEAT HIGH HEAT
LOWER DRYER LOWER DRYER
Set-Up Codes
PR MODELS: The set-up codes are the same as for the
PD models except where noted.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two or
three right-hand characters.
NOTE: The first line of each code indicates the factory default.
NOTE: Set-up codes marked with * are able to transfer from
one machine to another machine (must be same model type)
via USB stick.
Code
REGULAR CYCLE AMOUNT TO START*
606
Represents the amount of Coins or Gen 1 Debit Pulses
required to start a Regular Cycle. See Value of Coin 1 setting.
606 Advance from 0–39 by pressing the HEAVY DUTY
button. Factory default of 6 x coin 1.
600 PR MODELS ONLY: Factory default of 6 00, or
0 coins.
Press the NORMAL button once to advance to
■
next code.
705 REGULAR CYCLE DRY TIME*
Represents the amount of Regular Cycle Minutes per Coin
or Gen 1 Debit Pulses. Example - Regular Amount Start
Setting= 606 and Regular Cycle Dry Time Setting = 705 then
6X5=30. Regular Cycle Time is 30 Minutes.
705 Factory default of 5 minutes per coin.
By pressing the HEAVY DUTY button,
value adjusts from 1 to the maximum minutes.
745 PR MODELS: Represents the cycle length for free
cycles. Example: "7 45" = 45 minutes.
Press the NORMAL button once to advance to
■
next code.
800 TYPE OF DRYER PRICING*
Mode 8 allows the dryer to be set for Fixed Cycle or Fixed
Cycle with Top Off. See Types of Dyer Pricing for detailed
explanation.
800 Fixed Cycle with Top Off.
8 FC Fixed Cycle
Use the DELICATES button to change this selection.
COIN MODEL: Factory preset to 00.
Press the NORMAL button once to advance to
■
next code.
9 00 CYCLE COUNTER OPTION*
This option is either NOT SELECTED "OFF"
or SELECTED "ON."
Mode 9 allows you to keep track of how many cycles your
machine has done.
9 00 Not Selected "OFF."
9 0C Selected "ON" and not able to be deselected.
Press the DELICATES button 3 consecutive times
■
to select "ON." Once selected "ON," it cannot be
deselected.
Press the NORMAL button once to advance to
■
next code.
Explanation
15