Bosch SmartphoneGrip BSP3200 Notice D'utilisation D'origine page 11

Operation
Starting Operation
Place your smartphone in the SmartphoneGrip.
Start the eBike Flow app to have riding data displayed.
Depending on the smartphone's operating sys-
tem, the eBike Flow app can be downloaded
free of charge from the Apple App Store and
the Google Play store.
Use your smartphone to scan the code in order
to download the eBike Flow app.
Charging your Smartphone
While the smartphone is in the SmartphoneGrip, it can be
charged at the same time as displaying riding data. If your
smartphone has an inductive charging function, you can
charge the smartphone without needing a cable.
Inductive Charging
The charging process starts automatically when you place a
smartphone with an inductive charging function in the
SmartphoneGrip. The status LED (9) lights up yellow. When
the smartphone is fully charged, the status LED (9) will light
up green permanently.
The charging voltage is switched off when you remove the
smartphone from the SmartphoneGrip.
Charging via USB
If your smartphone does not have an inductive charging
function, you can charge your smartphone via the USB
port (3). To do so, open the USB cap and connect a separate
USB cable (not included in the scope of delivery) to the Mi-
cro-A/B USB port.
Pay attention to the type of plug required for your smart-
phone when purchasing the USB cable.
Note: If the eBike battery reaches a state of charge of
0 %, remove any loads that may be present (e.g. smart-
phone).
Status Indicators
The status LED (9) indicates the following statuses with dif-
ferent colours and lighting patterns.
Status
Charging via USB
Inductive charging starts
Inductive charging
Fully charged
Error message
The following alarm states are detected and will lead to the
inductive charging process being interrupted:
– Detection of foreign objects, e.g. coins, keys and other
metallic objects
Bosch eBike Systems
Behaviour
LED lights up blue.
LED flashes yellow 3 times.
LED lights up yellow.
LED lights up green.
LED flashes red.
– Temperature alarm
If the SmartphoneGrip is outside of the operating temper-
ature range, the status LED (9) will light up red and the
charging process is interrupted. The charging process will
resume as soon as the SmartphoneGrip is back within the
operating temperature range.
– Overvoltage alarm at voltages above 6 V
– Undervoltage alarm at voltages below 4.2 V
Maintenance and servicing
Maintenance and cleaning
Use a soft cloth dampened only with water for cleaning. Do
not use cleaning products of any kind.
Have all repairs performed only by an authorised bike
u
dealer.
Do not clean any of the components with pressurised water.
After-sales service and advice on using products
If you have any questions about the eBike and its compon-
ents, contact an authorised bicycle dealer.
For contact details of authorised bike dealerships, please
visit www.bosch-ebike.com.
Further information on the eBike components
and their functions can be found in the Bosch
eBike Help Center.
Transport
If you transport your eBike attached to the outside of
u
your car, e.g. on a bike rack, remove the Smart-
phoneGrip and the eBike battery (exception: built-in
eBike battery) to avoid damaging them.
Disposal and substances in products
You can find information about substances in products at the
following link:
www.bosch-ebike.com/en/material-compliance.
Do not dispose of eBikes and their components with house-
hold waste.
An in-store return is possible, provided the retailer voluntar-
ily offers a return or is legally obligated to do so. Refer to the
national regulations in this case.
The drive unit, on-board computer incl. operat-
ing unit, eBike battery, speed sensor, ac-
cessories and packaging should be disposed of
in an environmentally correct manner.
Check that your personal data has been deleted from the
device.
Batteries that can be removed from the power tool without
destruction must be removed before disposal itself and sor-
ted for separate battery collection.
English – 3
0 275 008 3SG | (09.02.2024)