Publicité
Les langues disponibles
Les langues disponibles
Page 5 of 13
increase slightly. Then apply a quarter turn. Tighten to 40Nm of torque (do not
exceed this figure, as damage can occur to the motorcycle and the bolt).
•
Fit the crash protector caps (item 1) as shown in picture A on page 1.
•
Before riding please check both crash protectors are secure and will not rotate.
•
Please check tightness of crash protectors regularly.
Off side (right side as you sit on the motorcycle)
•
Remove the bolt in position arrowed in picture B on page 1.
•
Place one of the M12 washers (item 3) onto the remaining longer M12 hex bolt
(item 9) followed by the smallest spacer (item 7) and then one of the shake
proof washers (item 4) as shown in picture 2.
•
Place the bolt with washers and spacer into the remaining crash protector (item
5), then place the remaining spacer (item 8) over the exposed end of the bolt as
shown in picture 2.
•
Offer this assembly into position as shown in picture B on page 1 (please ensure
no parts come into contact with any fairing panels). Finally tighten the crash
protector bolt until you feel some compression from inside the protector using
19mm socket and wrench. PLEASE NOTE THE CRASH PROTECTOR MUST BE
POSITIONED AS IN PICTURE 'C' ON PAGE 3 WITH THE BIGGER END
TOWARD FRONT OF BIKE. Turn a little more so that you feel the compression
increase slightly. Then apply a quarter turn. Tighten to 40Nm of torque (do not
exceed this figure, as damage can occur to the motorcycle and the bolt).
•
Fit the crash protector caps (item 1) as shown in picture B on page 1.
•
Before riding please check both crash protectors are secure and will not rotate.
•
Please check tightness of crash protectors regularly.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G
may make design changes which do not diminish their performance or visual appeal and supplying them in
such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to
title) has been given or will apply to the Products other than those in R&G's order or confirmation and the
Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular
purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care
and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any
defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall
not be liable if the Products have been modified or used or maintained otherwise than in accordance with
R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal
injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the
amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the
Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned
direct to us if they were purchased direct from us (customer must prove if necessary).
returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G. All returns are
subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at
time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products,
unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
ISSUE 1 02/07/2020 (NSY)
CONSUMER NOTICE
R&G RETURNS POLICY (NON-FAULTY GOODS)
R&G
CP0491
Otherwise to be
Publicité
