Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Page 1 of 13
CP0491
FITTING INSTRUCTIONS FOR CP0491 AERO CRASH PROTECTORS
FOR BMW F900R (REAR) & F900XR 2020
PICTURE A
PICTURE B
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF
OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE
.
WAY OF MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Publicité
Manuels Connexes pour R&G CP0491
Sommaire des Matières pour R&G CP0491
- Page 1 Page 1 of 13 CP0491 FITTING INSTRUCTIONS FOR CP0491 AERO CRASH PROTECTORS FOR BMW F900R (REAR) & F900XR 2020 PICTURE A PICTURE B HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY...
- Page 2 Page 2 of 13 CP0491 TOOLS REQUIRED GENERAL TORQUE SETTINGS M4 BOLT = 8Nm • Socket set to include 19mm A/F socket and wrench. M5 BOLT = • T55 Torx’s bit or key. M6 BOLT = • Torque wrench (up-to 40Nm).
- Page 3 Page 3 of 13 CP0491 RIGHT-HAND SIDE ASSEMBLY AERO STYLE CRASH PROTECTOR ORIENTATION PICTURE C R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 4 Page 4 of 13 CP0491 PICTURE 1 PICTURE 2 FITTING INSTRUCTIONS • It is advisable to support the engine to prevent any engine movement when the original engine bolts are loosened/removed (do not use excessive force as damage can occur).
- Page 5 Page 5 of 13 CP0491 increase slightly. Then apply a quarter turn. Tighten to 40Nm of torque (do not exceed this figure, as damage can occur to the motorcycle and the bolt). • Fit the crash protector caps (item 1) as shown in picture A on page 1.
- Page 6 Page 6 of 13 CP0491 NOTICE DE MONTAGE POUR CP0491 PROTECTIONS CRASH POUR BMW F900R (ARRIÈRE) & F900XR 2020 PHOTO A PHOTO B E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES...
- Page 7 Page 7 of 13 CP0491 OUTILS REQUIS VALEURS DE SERRAGE M4 BOULON = 8Nm • Clé à cliquet + douille 19mm. M5 BOULON = • Clé Torx T55. M6 BOULON = • Clé dynamométrique (jusqu’à 40Nm). M8 BOULON = 20Nm...
- Page 8 Page 8 of 13 CP0491 ASSEMBLAGE CÔTÉ GAUCHE ASSEMBLAGE CÔTÉ DROIT NOTICE DE MONTAGE • Il est conseillé de soutenir le moteur pour empêcher tout mouvement du moteur lorsque les boulons du moteur d'origine sont desserrés / retirés (ne pas utiliser une force excessive car des dommages peuvent survenir).
- Page 9 Page 9 of 13 CP0491 à 40 Nm de couple (ne pas dépasser ce chiffre, car des dommages peuvent se produire sur la moto et le boulon). • Montez les capuchons de protection crash (article 1) comme indiqué sur la photo A en page 1.