Publicité
Les langues disponibles
Les langues disponibles
|
Replacement Parts Information
For repairs or routine maintenance, Fill-Rite offers the parts you need. The following parts diagram and list covers all applicable parts for your Fill-Rite product. These
parts can be obtained through any authorized Fill-Rite dealer. Be sure to use only genuine Fill-Rite replacement parts for your service and maintenance needs. For a
list of authorized dealers, please visit our web site at fillrite.com.
WARNING
DO NOT open or attempt to repair the motor on your NX25-DDC pump. Opening the motor case can compromise the integrity of the Explosion
Proof construction and will void any existing warranty and certification (UL listing). Please refer to the Warranty Policy located on page 2.
KIT321RK - Overhaul repair kit
KIT321RG - Rotor kit
KIT320SL - Shaft seal kit
KIT321FLG - Flange kit
Servicing Rotor, Vanes, and Shaft Seals
The rotor, vanes, and shaft seals are inside the pump housing, and are accessed
through the rotor cover located on the face of the pump. It is held in place with
three 4mm hex drive attaching bolts. You can access the rotor and vanes for
inspection and cleaning, but DO NOT attempt to remove the shaft seals without
a new seal kit to install.
Always inspect the rotor cover seal and mating surface (groove) for nicks or
damage prior to reassembly. Be certain o-ring is not pinched to prevent leakage.
Torque the attaching hardware to 44 in-lbs.
fillrite.com
NX25-DDC SERIES DC FUEL TRANSFER PUMPS
KIT321BV - Bypass kit
PART NUMBER
ITEM NO.
KIT321SK
1
2
3
4
KIT321NB - Nozzle boot kit
KIT321SK - External seal kit
DENOTES DIMENSION CRITICAL TO QUALITY
C
NOTICE
THIS DRAWING AND THE PRINCIPLES AND ELEMENTS OF DESIGN
EMBODIED THEREIN ARE THE EXCLUSIVE PROPERTY OF
TUTHILL CORPORATION, TUTHILL TRANSFER SYSTEMS
BE COMMUNICATED, DISCLOSED, REPRODUCED OR USED EXCEPT AS PREVIOUSLY
AUTHORIZED IN WRITING BY SAID COMPANY AND MUST NOT BE SUBMITTED TO
OUTSIDE PARTIES FOR EXAMINATION WITHOUT THE CONSENT OF SAID COMPANY
MUST BE RoHS COMPLIANT
PART NUMBER
kit321sw
PART NUMBER
DESCRIPTION
OFF/QTY.
SHIPPING ENVELOPE
1
SL000843-000
O-RING, BUNA-N, 2-036
1
100F0790
GASKET, INLET FLANGE
1
100F0760
INLET SCREEN
1
0
011248
01/05/16
KIT, NX3200 SERIES EXTERNAL SEAL REPAIR
REV
ECN NUMBER
DATE
PART NUMBER
MATERIAL
AS NOTED PER PART PRINTS
KIT321SK
UNLESS OTHERWISE SPECIFIED
AND ARE NOT TO
DIMENSIONS ARE IN INCHES
9/1/2017
THIRD ANGLE
DATE
TWO PLACE DECIMAL
0.01
PROJECTION USED
THREE PLACE DECIMAL
0.005
SCS
DWN
FOUR PLACE DECIMAL
0.0005
ANGULAR
0.5
1 OF 1
SHEET
MACHINED SURFACE FINISH
64 µ" AA MAX
R
INSTALLATION AND OPERATION MANUAL
ITEM NO.
PART NUMBER
1
SA001885-000
2
FS001881-000
3
700F2950
4
MF000507-001
KIT321BG - Inlet kit
KIT321SW - Switch kit
0
011248
01/05/16
REV
ECN NUMBER
DATE
DENOTES DIMENSION CRITICAL TO QUALITY
MATERIAL
PER PART PRINTS
C
UNLESS OTHERWISE SPECIFIED
NOTICE
THIS DRAWING AND THE PRINCIPLES AND ELEMENTS OF DESIGN
EMBODIED THEREIN ARE THE EXCLUSIVE PROPERTY OF
TUTHILL CORPORATION, TUTHILL TRANSFER SYSTEMS
AND ARE NOT TO
DIMENSIONS ARE IN INCHES
THIRD ANGLE
BE COMMUNICATED, DISCLOSED, REPRODUCED OR USED EXCEPT AS PREVIOUSLY
TWO PLACE DECIMAL
0.01in
PROJECTION USED
AUTHORIZED IN WRITING BY SAID COMPANY AND MUST NOT BE SUBMITTED TO
THREE PLACE DECIMAL
0.005in
OUTSIDE PARTIES FOR EXAMINATION WITHOUT THE CONSENT OF SAID COMPANY
FOUR PLACE DECIMAL
0.0005in
ANGULAR
0.5°
MUST BE RoHS COMPLIANT
MACHINED SURFACE FINISH
64 µ" AA MAX
KIT321ASN - Anti-siphon kit
DESCRIPTION
QTY.
ASSEMBLY; MOTOR SWITCH
1
LHSHCS; M6 X 1.0 X 14MM
2
LOCK NUT, 5/16-18
1
LEVER; SWITCH
1
KIT, NX3200 SERIES SWITCH ASSEMBLY
PART NUMBER
kit321sw
9/15/2017
DATE
SCS
DWN
1 OF 1
SHEET
R
12
Publicité
