Bosch GBH 18V-36 C Professional Notice Originale page 9

Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Assembly
Before carrying out any work on the power tool (e.g.
u
maintenance, tool change, etc.) as well as during
transport and storage, press the lock-on button to
lock the on/off switch. There is risk of injury from unin-
tentionally pressing the on/off switch.
Inserting the Bluetooth® Low Energy Module
GCY 42 (Accessory)
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.
Auxiliary handle
Do not operate your power tool without the auxiliary
u
handle (13).
Make sure that the auxiliary handle is always
u
tightened. Otherwise you could lose control of the power
tool when working.
Swivelling the auxiliary handle (see figure A)
You can swivel the auxiliary handle (13) to any angle for a
safe work posture that minimises fatigue.
– Turn the lower gripping end of the auxiliary handle (13)
anticlockwise and swivel the auxiliary handle (13) into
the required position. Then turn the lower gripping end of
the auxiliary handle (13) clockwise to retighten it.
Make sure that the retaining strap of the auxiliary handle
slots into the corresponding groove of the housing.
Bosch Power Tools
Selecting drill chucks and tools
For hammer drilling and chiselling, you will need SDS max
tools, which insert into the SDS max drill chuck.
Capacity Changing the Tool
80–100 %
The dust protection cap (3) largely prevents the penetration
of drilling dust into the tool holder during operation. When
60–80 %
inserting the tool, make sure that the dust protection cap (3)
40–60 %
does not become damaged.
20–40 %
Replace a damaged dust protection cap immediately.
u
5–20 %
It is recommended that you have use an after-sales
service for this.
0–5 %
Changing the Tool
Inserting the Application Tool (see figure B)
With the SDS max tool holder, you can change the applica-
tion tool simply and easily without additional aids.
– Clean and lightly grease the shank of the application tool.
– Insert the application tool into the tool holder while turn-
ing it until it locks automatically.
– Check that it is locked by pulling on the tool.
Removing the application tool (see figure C)
– Push the locking sleeve (4) back and remove the applica-
tion tool.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Start-up
Ensure that the cover (11) of the Bluetooth
u
Module GCY 42 is closed during operation. This will pre-
vent dust from getting in.
Setting the Operating Mode (see figure D)
You can use the combi switch (5) to select the operating
mode of the power tool.
English | 9
®
Low Energy
1 609 92A 9CN | (16.05.2024)