EINHELL TP-ET 18 Li BL Mode D'emploi page 12

or Rechargeable (Nickel Cadmium, Nickel
Metal Hydride, or Lithium-Ion) batteries.
6. Do not dispose of batteries in fi re.
7. Batteries should be recycled or disposed of
as per state, provincial and local guidelines.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
Special safety instructions
•
Hold the power tool by insulated gripping
surfaces only, because the cutter may
contact its own cord. Cutting a "live"wire
may make exposed metal parts of the power
tool "live" and could give the operator an
electric shock.
•
Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by your
hand or against the body leaves it unstable
and may lead to loss of control.
•
Before you put the electric router into
operation, check to ensure that the routing
tool is firmly seated and runs smoothly!
•
Never use a low quality or damaged routing
cutter.
•
Only use routing cutters whose shaft
diameter complies with the specifications in
the instructions.
•
The maximum speed specified for the routing
cutters is not allowed to be exceeded.
•
Never cut over metal parts, screws, nails, etc.
•
To avoid damage to the router, make sure
there are no foreign objects stuck to the
workpiece.
•
Always guide the router with both hands.
•
Let the router reach full speed before
plunging the routing cutter into the workpiece.
•
If the router becomes clogged with work
debris, switch it off. Let the router run to a
complete stop. Remove the debris with a long
stick and not with your fingers.
•
Let the router run to a complete stop before
removing the workpiece or setting down the
tool.
•
Always cut on a counter-rotating basis.
•
Watch out for the reaction torque of the tool,
especially if the router becomes jammed.
•
When you have finished your work, slide the
tool back to starting position.
•
Use only properly sharpened routing cutters.
•
Clamp the routing cutter by friction-locking.
•
For deep cuts, carry out the work in several
Anl_TP_ET_18_Li_BL_SPK7_USA.indb 12 Anl_TP_ET_18_Li_BL_SPK7_USA.indb 12
EN
steps according to the material in question.
•
Use only cutters with a shaft diameter which
matches the integrated clamp.
•
Use only cutters which are suitable for the
speed of the electric tool.
SAVE THESE INSTRUCTIONS
2. Layout and items supplied
2.1 Layout
1. Cordless routing unit
2. Unlock/lock button
3. On/Off switch
4. Speed adjusting dial
5. Spindle lock
6. Collet nut
7. Handle
8. Height adjuster lock knob
9. Height adjuster knob
10. Edge guide lock knob
11. Fixed base dust chute
12. Countersunk head screw for fi xed base dust
chute
13. Open-ended wrenches
14. Template guide
15. ⁄ " Collet
1
4
16. Router bit (not supplied)
17. Trimmer roller guide
17.1. Guide roller
17.2. Retaining knob
17.3. Adjustment knob
18. Compass point
19. Edge guide
19.1. Wing nut
20. Fixed base
21. LED lamp
22. Fixed base scale
23. Countersunk head screws
24. Fixed base cover
25. Battery (not supplied)
26. Push lock button
27. Battery capacity indicator
28. Battery capacity indicator button
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
store where you made your purchase at the latest
within 5 work days after purchasing the article and
upon presentation of a valid bill of purchase.
•
Open the packaging and take out the
- 12 -
27.07.2023 08:03:51 27.07.2023 08:03:51