Télécharger Imprimer la page

Franke TL 62 M Manuel D'installation Et Mode D'emploi page 12

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 36
EN
Semiautomatic programme with duration or
end time
Programme time setting
To select the programme duration or end time
X
X
press the Mode or Set button twice and set the
required time with the + and – buttons.
During duration or end time adjustment mode
selection, the corresponding Auto symbol
flashes.
Once a programme duration is set, the end
time cannot be decreased. Likewise, the
duration of a programme cannot be prolonged
once the end time is set.
Programme run
When the automatic programme is in progress
(and therefore the cooking function is active),
the Auto symbol remains lit and the remaining
cooking time appears on the display in
countdown form. The symbol
Automatic programme end
At the end of the programme duration or when
the end time is reached, the corresponding
symbol
goes off.
At the end of the automatic programme, the
Auto symbol flashes, the display shows "End"
and an intermittent acoustic signal (which can
be stopped by pressing any button) sounds.
Timer function
The timer allows the setting of a time from which a
countdown begins. This function does not turn the
oven on or off, but only sounds an audible alarm
when the time has elapsed.
Press the Mode or Set button once; the display
X
X
shows:
The bell symbol flashes, then the alarm
duration can be set with the + and – buttons.
When this function is active, the bell symbol
remains lit and the display shows the remaining
time (countdown).
At the end of the time an acoustic signal
(which can be stopped by pressing any button)
sounds.
Modifying/deleting data
The set data can be changed at any time by
X
X
pressing the + and - buttons together.
Cancelling the cooking duration automatically
ends the function, and vice versa.
Note: The oven stays hot at around the set cooking
temperature for a long time after it has been
switched off; therefore to avoid overcooking or
burning the food, it is advisable to remove it from
the oven.
Switching on the first time
When using the oven for the first time, operate it
X
X
empty with the temperature knob set to maximum
for at least 40 minutes, keeping the door
completely open and airing the room.
also remains lit.
Suggestions
For successful cooking, never place your dishes in
Z
X
the oven when it is cold; wait until it has reached
the set temperature.
During cooking, never place pots or containers
Z
X
directly on the oven floor;
9 place them above the grills or drip-trays provided,
on one of the 5 shelves available;
Never cover the walls of the oven with aluminium
Z
X
foil, especially in the lower part of the cooking
compartment.
Any repairs must be carried out by specialised,
Z
X
licensed personnel. Contact our nearest service
centre and demand only original spare parts.
Your FRANKE oven uses a special enamel which
Z
X
is easy to keep clean, however it is advisable to
clean it frequently to avoid baking on grime and
previous cooking residues.
Any self-cleaning panels (if provided) can be
Z
X
cleaned with soap and water (see cleaning
instructions).
Note: Before switching the oven on, read the timer
instructions (see page 10).
If the oven has an automatic cooking or switching off
programmer, select the „manual" option indicated by
the
– 12 –
In case of programmed operation, the
appliance will not accept end of cooking times
prior to those of start of cooking proposed by
the appliance itself.
The odour noticed during this operation is
due to the evaporation of substances used to
protect the oven during the period between
manufacture and installation.
After the 40 minutes, the oven will be
ready to use.
failure to do so could damage the oven
enamel.
symbol to use the oven in manual mode.

Publicité

loading

Ce manuel est également adapté pour:

Cr 66 mCs 66 mSg 62 mSm 62 mSm 66 mCm 65 m ... Afficher tout