Télécharger Imprimer la page

Skil 7208 Notice Originale page 10

Masquer les pouces Voir aussi pour 7208:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
• Holding and guiding the tool 0
! while working, always hold the tool at the
grey-coloured grip area(s)
- guide the tool parallel to the working surface
! do not apply too much pressure on the tool; let
the sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep ventilation slots H 2 uncovered
APPLICATION ADVICE
• Use the tool with its standard foot plate for large working
surfaces, corners and edges !
• Use the tool with the special sanding attachments for
hard-to-reach places @
• The flexible sanding attachment is intended for
- rounding edged surfaces #a
- all rounded surfaces with a maximum diameter of
10 cm #b
• When the delta-tip is worn or damaged at the top, you
may extend its service life twice by removing it, turning it
120° and putting it back (also applicable to delta sanding
sheet) $
• Never use the same sanding sheet for wood and metal
• Recommended sanding belt grits:
coarse
- for removing paint; for sanding of
extremely rough wood
medium
- for sanding of rough or plain wood
fine
- for smoothing of wood; for finishing of
bare wood; for smoothing surfaces with
old paint
• Use different grit sizes when the working surface is
rough:
- start sanding with coarse or medium grit
- finish with fine grit
• For more tips see www.skileurope.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots H 2)
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol % will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this product
is in conformity with the following standards or
standardized documents: EN 60745, EN 61000,
EN 55014, in accordance with the provisions of the
directives 2006/95/EC, 2004/108/EC, 2006/42/EC
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
03.05.2011
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 71 dB(A) and the sound
power level 82 dB(A) (standard deviation: 3 dB), and the
vibration 14.3 m/s² (hand-arm method; uncertainty
K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintainted accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Ponceuse polyvalente
INTRODUCTION
• Cet outil sert au ponçage et au polissage à sec du bois,
des surfaces peintes, du plastique et du mastic
• Cet outil n'est conçu pour un usage professionnel
• Lisez et conservez ce manuel d'instruction 3
SPECIFICATIONS TECHNIQUES 1
10
7207/7208

Publicité

loading

Ce manuel est également adapté pour:

7207