Publicité
Les langues disponibles
Les langues disponibles
Playback procedure
1
Press OPEN/CLOSE.
The disc tray will open.
2
Place a disc onto the tray.
Hold the disc, position it with the printed label side up, align
it with the guides, and place it in its proper position.
3
Press PLAY or OPEN/CLOSE.
The disc tray closes automatically.
On the screen,
changes to "Reading" and then play-
back will commence.
• A menu screen may appear on the TV screen, if the
disc has a menu feature. In this case, press
,
or ENTER to operate a menu feature.
4
Press STOP to end playback.
• The DVD/VCR memorizes the stopped point, depend-
ing on the disc. "
" appears on the screen. Press PLAY
to resume playback (from the scene point).
• If you press STOP again("
or unload the disc, the DVD/VCR will clear the stopped
point.
5
Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press POWER.
The disc tray closes automatically and DVD/VCR turns off.
NOTES:
•
If a non-compatible disc is loaded, "Incorrect Disc", "Region
Code Error" or "Parental Error" will appear on the TV screen
according to the type of loaded disc. In this case, check your
disc again (See page 27 and 32).
•
Some discs may take a minute or so to start playback.
A "Prohibition" symbol
•
screen. This symbol means either the feature you tried is not
available on the disc, or the DVD/VCR can not access the
feature at this time. This does not indicate a problem with
the DVD/VCR.
•
When you set a single-faced disc label downwards (ie. the
wrong way up) and press PLAY or OPEN/CLOSE, "Reading"
will appear and remain on the screen for approx. 40 seconds
and then it will change to "Incorrect Disc".
•
Some playback operations of DVDs may be intentionally fixed
by software producers. Since this DVD/VCR plays DVDs ac-
cording to the disc contents the software producers designed,
some playback features may not be available. Also refer to
the instructions supplied with the DVDs.
•
When playing DTS-encoded Audio CDs, excessive noise will
be heard from the analog stereo outputs. To avoid possible
damage to the audio system, the consumer should take
proper precautions when the analog stereo outputs of the
DVD/VCR are connected to an amplification system.
28
,
" appears on the screen)
may appear at the upper left of the
Special playback
NOTE:There may be a slight delay between pressing the
button and the function activation.
Fast Forward Playback
Press F.FWD during normal playback.
Each press of F.FWD will increase the speed of the search
(x2),
(x4),
• To resume normal playback, press PLAY.
Review Playback
Press REW during normal playback.
Each press of REW will increase the speed of the search
(x2),
(x4),
,
• To resume normal playback, press PLAY.
Still Playback
Press PAUSE/STILL during normal playback.
• To resume normal playback, press PLAY.
Frame Advance
Press PAUSE/STILL during still playback.
One frame is advanced each time you press PAUSE/STILL.
• To resume normal playback, press PLAY.
Slow-motion Playback
Press SLOW during normal playback or still playback.
Each press of SLOW will change the speed of the slow x1/2,
x1/4, x1/6, x1/7.
• To resume normal playback, press PLAY.
• To resume the still playback, press PAUSE/STILL.
Locating a chapter or track
Press SKIP (
) Forward or SKIP (
playback to locate a chapter that you want to watch.
Each time you press the button, a chapter or track is skipped.
NOTE:
The unit is capable of holding a still video image or On screen
display image on your television screen indefinitely. If you leave
the still video image or On screen display image displayed on
your TV for an extended period of time, you risk permanent
damage to your television screen. Projection televisions are
very susceptible.
Zooming
This unit will allow you to zoom in on the frame image. You
can then make selections by switching the position of the
frame.
1
Press ZOOM during playback.
The center part of the image will be zoomed in.
Each press of ZOOM will change the ZOOM
(x 1.3),
2 (x 1.5) and
2
Press
/
or
/
You may move the frame from the center position to UP,
DOWN, LEFT or RIGHT direction.
3
In the zoom mode press ZOOM repeatedly to return to a
1:1 view (
Off).
NOTE:
You can use the Pause, Slow, Search or Skip feature in the
zoom mode.
(x8),
(x20).
(x8),
(x20).
) Reverse during
1
3 (x 2.0).
to view a different part of the frame.
Publicité
