Spare Parts Lists; Manufacturer's Warranty - REMS Hot Dog 2 Notice D'utilisation

eng
3.2. Soldering material
For soft solder use REMS Lot Cu 3. Copper pipes- and fi ttings must be clean. soft solder soft solder use REMS Lot Cu 3. Copper pipes- and fi ttings must be clean.
For the preparation of the solder point put REMS Paste Cu 3 onto the pipe.
This paste contains solder powder and fl ux. The advantages of this paste are
that the required temperature for soldering is visible through the change of
colour of the paste and that a better fi lling of the soldering point is gained. In
any case however REMS Lot Cu 3 has to be added. REMS Lot Cu 3 and REMS
Paste Cu 3 have been specially developped for drinking water installations and
correspond to the respective DIN standards.
4. Maintenance
Notwithstanding the maintenance described below, it is recommended to send
in the power tool to an authorised REMS contract customer service workshop
for inspection and periodic testing of electrical devices at least once a year. In
Germany, such periodic testing of electrical devices should be performed in
accordance with DIN VDE 0701-0702 and also prescribed for mobile electrical
equipment according to the accident prevention rules DGUV, regulation 3
"Electrical Systems and Equipment". In addition, the respective national safety
provisions, rules and regulations valid for the application site must be considered
and observed.
4.1. Maintenance
WARNING WARNING
Pull out the mains plug before maintenance work!
Keep the solder fi ttings (1) free from solder and fl ux. These impair the heat
transfer. Clean the solder fi ttings with a wire brush when hot if necessary. Clean
plastic parts (e.g. housing) only with REMS CleanM machine cleaner (Art. No.
140119) or a mild soap and a damp cloth. Do not use household cleaners These
often contain chemicals which can damage the plastic parts. Never use petrol,
turpentine, thinner or similar products for cleaning.
Make sure that liquids never get onto or inside the drive unit. Never immerse
the drive unit in liquid.
4.2. Inspection/repair
WARNING WARNING
Pull out the mains plug before carrying out maintenance or repair work!
This work may only be performed by qualifi ed personnel.
5. Faults
Fault: Solder does not melt.
Cause:
● Solder fi ttings do not get
hot.
● Power cable defective.
6. Disposal
REMS Hot Dog 2 may not be thrown in the domestic waste after use. It must
be disposed of properly by law.

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which REMS is not responsible, shall be excluded from the warranty
Services under the warranty may only be provided by customer service stations
authorized for this purpose by REMS. Complaints will only be accepted if the
product is returned to a customer service station authorized by REMS without
prior interference and in a fully assembled condition. Replaced products and
parts shall become the property of REMS.
The user shall be responsible for the cost of shipping and returning the product.
A list of the REMS-authorized customer service stations is available on the
Internet under www.rems.de. For countries which are not listed, the product
must be sent to the SERVICE-CENTER, Neue Rommelshauser Strasse 4,
71332 Waiblingen, Deutschland. The legal rights of the user, in particular the
right to make claims against the seller in case of defects as well as claims due
to wilful violation of obligations and claims under the product liability law are
not restricted by this warranty.
Remedy:
● Have the REMS Hot Dog 2 checked/
repaired by an authorised REMS customer
service workshop.
● Have the power cable changed by
qualifi ed personnel or an authorised REMS
customer service workshop.
This warranty is subject to German law with the exclusion of the confl ict of laws
rules of German International Private Law as well as with the exclusion of the
United Nations Convention on Contracts for the International Sales of Goods
(CISG). Warrantor of this world-wide valid manufacturer's warranty is REMS
GmbH & Co KG, Stuttgarter Str. 83, 71332 Waiblingen, Deutschland.

8. Spare parts lists

For spare parts lists, see www.rems.de → Downloads → Parts lists.
eng
7