Publicité
Les langues disponibles
Les langues disponibles
English
Application
Siedle Basic video set in bus tech-
nology with the functions calling,
speech, vision and door release.
Number of integrated call buttons:
1–2
Each Basic set can be expanded with
selected door and indoor stations,
and enhanced with switching func-
tions and a telephony connection.
CV 850-...-02 door station perfor-
mance features:
• Integrated camera with automatic
day/night switchover, LED lighting
and 2-stage heating
• Integrated door loudspeaker
• Adjustable voice volume
• Number of integrated call buttons:
1 (CV 850-1-02), 2 (CV 850-2-02)
• Acoustic button acknowledgement
can be activated
• Backlit nameplates exchangeable
from the front
• For surface mounting with housing
front made of high-quality plastic
VIB 150-0 indoor station perfor-
mance features:
• 8.8 cm (3.5 inch) TFT colour dis-
play
• Colour and brightness can be set
in seven stages
• Speech and call volume can be set
in five stages
• 11 call tones
• Call differentiation: Storey call,
2 door calls and internal call from
standard/deluxe indoor stations
• LED status display: Incoming calls,
active call, muting
• Door release/light function via the
bus line
• Manual door connection even
without a door call
• Parallel switching of max. 4 indoor
stations without internal speech
operation
• Handy 2-step mounting: Base plate
with terminals can be pre-installed,
toolless final assembly
14
SNG 850-0 set line rectifier per-
formance features:
• 10 bus addresses for supplying the
bus users
• Integrated door release and light
contact
• Programming: manual, Plug+Play
or via BPS 650-... (Windows PC)
with ZBVG 650-... and
PRI 602-... USB
Electrical voltage
• Mounting, installation and ser-
vicing work on electrical devices may
only be performed by a suitably
qualified electrician.
Failure to observe this regulation
could result in the risk of serious
damage to health or fatal injury due
to electric shocks.
• Operation at an altitude of up to
2000 m above sea level.
• Observe EN 62368-1!
In a building installation, an all-
pole mains switch with a contact
opening of at least 3 mm must be
provided. The device must not be
exposed to water drops or sprayed
water! Sufficient ventilation must be
ensured. Pay particular attention to
ensure that ventilation slots are not
covered.
• When using stranded cores as
cable material, these must be fitted
with wire end ferrules without fail.
Electrostatic charging
As a result of electrostatic charging,
direct contact with the circuit board
can result in destruction of the
device. Direct contact with the circuit
board must therefore be avoided.
In the case of video systems, the fol-
lowing mounting situation must be
avoided at all costs:
• direct backlight
• direct sunlight
• very bright image backgrounds
• highly reflective walls opposite the
camera
• lamps or direct light sources
Scope of supply SET CVB 850-1
• CV 850-1-02
• VIB 150-...
• SNG 850-...
• Siedle screwdriver
• This product information
Scope of supply SET CVB 850-2
• CV 850-2-02
• 2 x VIB 150-...
• SNG 850-...
• Siedle screwdriver
• This product information
Mounting CV 850-...
1 Unscrew the front of the housing.
To do this, release the Siedle screw
on the underneath of the housing.
Hinge the front of the housing
forward.
2 Surface mounting the door sta-
tion. Recommended mounting
height appr. 1.50 m /4.9 ft. to centre
device. Please note: The cable is
inserted in the lower area of the
base plate!
3 Strip back the installation cable
close to the wall (appr. 10 mm)
and insert the cores into the base
plate. Fasten the base plate using 4
screws. Close the two openings at
the top using rubber stoppers. Install
in accordance with the terminal
diagram.
The cores may only be laid in the
admissible installation space.
4 The pick-up angle of the camera
can be mechanically preadjusted on
the vertical and horizontal by appr.
30° depending on the mounting
situation. To change the pick-up
direction of the camera, it can be
Publicité
