GYS IMS PRO 220E FV CEL Mode D'emploi page 20

WELDING PARAMETERS
WELDING INTENSITY SETTINGS
The following settings concern the intensity range that may be used depending on the electrode's type and diameter . These ranges are quite large
as they depend on the application and the welding position.
Ø electrode (mm)
1.6
2.0
2.5
3.15
4.0
5
ARCFORCE SETTINGS
It is recommended to set the arc force in median position (0) to start the welding and adjust it according to the results and welding preferences.
Note : the arcforce setting range is specific to the selected electrode type.
ADVANCED SETTINGS
Refer to the chapter « menu access » for more details regarding welding parameters.
The two MMA modes
: Hotstart Time, duration of the extra current at arc strike, expressed in seconds.
: Antisticking, active (On), the current will stop after 2 consecutive seconds of short circuit, inactive (Off), the current will not stop, even in
the event of long short circuit.
In MMA vertical up mode
: Frequency, determines the number of pulses per second (Hz).
: Percentage, determines the background/cold current expressed in percentage of the welding current.
: Duty cycle, determines the duty cycle expressed as a percentage of the pulsation frequency.
TUNGSTEN ELECTRODE WELDING WITH INERT GAS (TIG
CLAVIER MMA 200 A
CONNECTIONS AND RECOMMENDATIONS
COULEURS / COLORS :
TIG welding requires a torch as well as a gas bottle equipped with a regulator.
BLANC / WHITE
Connect the earth clamp to the positive connector (+).
PANTONE 427C
Connect the torch's earth cable to the negative plug (–).
PANTONE 429C
Connect the torch's gas hose to the regulator's output.
NOIR / BLACK
Ensure that the torch is equipped and ready to weld, and that the consumables (Vise grip, ceramic gas nozzle, collet and collet body) are not damaged.
VRD
The grey areas are not useful for this mode.
SELECTION MODE
TIG
Press button several times until the LED lights up under the symbol
MODE
TIG PULSE
Press button several times until the LEDs light up under the symbol
MODE
20
The pulsed TIG mode adds current pulsation to facilitate the welding of thin sheets while limiting temperature rise.
IMS 220E FV CEL
Rutile E6013 (A)
30-60
50-70
60-100
80-150
100-200
150-220
and come with the following additional settings :
, two extra settings are available :
125 x 90 mm
DÉCOUPE / CUT
BLANC TRANSLUCIDE / TRANSLUCENT WHITE
DÔMES / BUTTONS GUIDE DOIGT 1 MM
NOIR TRANSLUCIDE 70 % / TRANSLUCENT BLACK 70%
MMA
press 3 s
A
Basic
7018
V
Rutile Pulse
6013
Cellulosic
6010
HOT START
ARC FORCE
setup
memory
press 3s
I N V E R T E R
W E L D E R
TIG
Basic E7018 (A)
125-210
200-220
AND TIG VERTICAL UP
CLAVIER MMA 200 A
2018/11/08
COULEURS / COLORS :
BLANC / WHITE
PANTONE 427C
PANTONE 429C
NOIR / BLACK
TIG
Pulse
VRD
MODE
press 3s
.
and to the left of the symbol
Cellulosic E6010 (A)
30-55
50-80
80-110
90-140
Pulse
125 x 90 mm
DÉCOUPE / CUT
BLANC TRANSLUCIDE / TRANSLUCENT WHITE
DÔMES / BUTTONS
NOIR TRANSLUCIDE 70 % / TRANSLUCENT BLACK 70%
A
V
HOT START
ARC FORCE
press 3s
I N V E R T E R
W E L D E R
TIG (TIG VERTICAL UP)
The grey areas are not useful for this mode.
Pulse
.
EN
-
-
60-75
85-90
120-160
110-170
)
2018/11/08
GUIDE DOIGT 1 MM
MMA TIG
press 3 s
Basic
7018
Rutile Pulse Pulse
6013
Cellulosic
6010
MODE
setup
memory
press 3s