Publicité
Les langues disponibles
Les langues disponibles
8. Unpacking
• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating instructions before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
m WARNING!
The device and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!
9.
Assembly
Warning!
Always pull out the mains plug before carrying out
adjustments on the device.
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
• Always pull out the mains plug before carrying out
adjustments on the device.
• Pull out the mains plug before all maintenance and
assembly work.
• The machine must be stable, i.e. bolted down on a
workbench or similar. or similar.
• Prior to commissioning, all covers and safety devic-
es must be mounted correctly.
• The grinding disc must be able to run freely.
Safety instruction! Do not connect the device until all
assembly and adjustment work has been completed
and the operating manual and safety instructions have
been read and understood.
Tool support (left and right) (Fig. 1, 2, 2.1)
Fasten the tool support (4) to the grinding wheel guard
(6) with the mushroom head screw (M6x10) (a) and
the star grip nut (b). The distance between the grind-
ing disc (3) and the tool support (4) must be set to
max. 2 mm.
Spark protection with LED work lamp
(left and right) (Fig. 1, 3)
Fasten the spark guard (2) with LED work lamps (5)
to the grinding wheel guard (6) with two M5x8 pan
head screws (c).
The distance to the grinding wheel (3) should be not
more than 2mm. The distance between the spark
guard (2) and the grinding wheel (3) can be adjusted
by slackening the two pan head screws (c). Tighten
the screws securely.
LED work lamp (Fig. 1, 4, 4.1, 4.2)
The lighting (5) can be switched on by pressing the
switch (d) on the lamp. The lighting is switched off by
pressing the switch again.
Open the battery compartment (Fig. 4.1) to insert/
change the batteries (2xAAA R03 1.5 V). Insert the
batteries (2x on each side) (Fig. 4.2). If you change
the batteries dispose of the used batteries properly.
Replace the cover of the battery compartment in re-
verse order (Fig. 4.1).
Protective panels (Fig. 1, 5, 5.1)
Install the safety screen (1) on the LED work lamp
(5) with the M5x55 mushroom head screw (e) and the
knurled head screw (f).
The protection is individually adjustable so that the
user's eyes are protected during the grinding process.
10. Start up
m Attention!
Always make sure the device is fully assembled
before commissioning!
Switching on/off
• To switch on, set the ON/OFF switch (8) to the ON
position.
• To switch off, set the ON/OFF switch (8) to the OFF
position.
Do not start grinding until the device has reached its
maximum speed.
www.scheppach.com
GB | 25
Publicité
