Roger Beep - PRESIDENT WALKER II FCC Manuel D'utilisation

5. If no key is pressed, the unit exits
the display.
Default KEY BEEP is On.

3) ROGER BEEP

When the function is active, the icon
The Roger Beep sounds when the PTT switch (17) on the microphone is re-
leased in order to let your correspondent speak. Historically as transceiver
is a "simplex" communication mode, it is not possible to speak and to listen
at the same time (as it is the case with a telephone). Once someone had
finished talking, he said "Roger" in order to prevent his correspondent that
it was his turn to talk. The word "Roger" has been replaced by a significant
beep. There comes "Roger beep" from.
Press PUSH knob (6) for 3 seconds to
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the RG BP function.
2. Press PUSH knob (6) to validate.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
activate deactivate
to On / Of the function.
4. New press PUSH knob (6) to validate. The parameter stops blinking. a) Go
back to point 1 to adjust another function or b) Press the PTT switch (17) to
validate exit MENU.
and disappears.
5. If no key is pressed, the unit exits
the display.
Default ROGER BEEP is Of.
4) TONE
The TONE function is used to change
-5 to +5.
Press PUSH knob (6) for 3 seconds to
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the TONE function.
2. Press PUSH knob (6) to validate.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select a new value.
4. New press PUSH knob (6) to validate. The parameter stops blinking. a) Go
back to point 1 to adjust another function or b) Press the PTT switch (17) to
validate and exit MENU. disappears.
5. exits
If no key is pressed, the unit
the display.
Default TONE is 0.
MENU after 10 seconds, disappears in
appears on the display.
enter MENU.
is displayed.
The current status blinks on LCD.
MENU after 10 seconds, disappears in
the tone on reception. 11 levels from
enter MENU. is displayed.
The value of the tone blinks on LCD.
MENU after 10 seconds,
disappears in
5) DIMMER
The DIMMER function allows to
backlight or to set no backlight (OF).
Press PUSH knob (6) for 3 seconds to
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to the DIMMER function.
2. Press PUSH knob (6) to validate.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select a new value.
4. New press PUSH knob (6) to validate. The parameter stops blinking. a) Go
back to point 1 to adjust another function or b) Press the PTT switch (17) to
validate and exit MENU.
5.
If no key is pressed, the unit
the display.
Default DIMMER value is 9.
6) EMG SET 1
Allows to set the Priority Channel 1.
Press PUSH knob (6) for 3 seconds to
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to the EMG 1 function.
2. Press PUSH knob (6) to validate.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the channel.
4. New press PUSH knob (6) to validate. The channel stops blinking. a) Go
back to point 1 to adjust another function or b) Press the PTT switch (17) to
validate and exit MENU.
5.
If no key is pressed, the unit
the display.
Default Priority channel 1 is 9.
See § PRIORITY CHANNELS page 9.
7) EMG SET 2
Allows to set the Priority Channel 2.
Press PUSH knob (6) for 3 seconds to
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the EMG 2 function.
Points 2 to 5 are identical to § EMG SET 1.
Default Priority channel 2 is 19.
See § PRIORITY CHANNELS page 9.
11
adjust
the brightness (from 1 to 9) of the
enter MENU. is displayed.
The value of the dimmer blinks on LCD.
disappears.
exits MENU after 10 seconds,
disappears in
enter MENU. is displayed.
The channel blinks on LCD.
disappears.
exits MENU after 10 seconds,
disappears in
enter MENU. is displayed.