How To Use Your Transceiver; Manual Squelch - PRESIDENT WALKER II FCC Manuel D'utilisation

* Adjustment with external SWR-meter (e.g. TOS-1 PRESIDENT)
a) To connect the SWR meter :
- Connect the SWR meter between the CB radio and the antenna as close as
possible to the CB (use a maximum of 15.75 in / 40 cm cable, type President
CA 2C).
b) To adjust the SWR meter:
- Set the CB on channel 20.
- Put the switch on the SWR-meter to position FWD (calibration).
Press the PTT "push-to-talk" switch (17) on the microphone to transmit.
-
- Bring the index needle to  by using the calibration key.
- Change the switch to position REF (reading of the SWR level). The reading on
the Meter should be as near as possible to 1. If this is not the case, readjust
your antenna to obtain a reading as close as possible to 1. (A SWR reading
between 1 and 1.8 is acceptable).
- It will be necessary to recalibrate the SWR meter after each adjustment of
the antenna.
WARNING: In order to avoid any losses and attenuations in cables used for
connection between the radio and its accessories, PRESIDENT recommends
to use a cable with a length inferior to 118.11 in / 3 m).
Your transceiver is now ready for use.
B) HOW TO USE YOUR TRANSCEIVER
1) ON/OFF ~ VOLUME
Turn on : turn VOLUME knob (1) clockwise. If the function KEY BEEP is active
(see menu KEY BEEP page 10), the radio emits a beep. The radio is "on".
Display shows the microphone type setup during 1 second . See menu MIC
TYPE page 12.
Turn Off : turn VOLUME knob (1) counterclockwise until radio emits click
sound. Your radio is "off".
Volume Adjustment: rotate VOLUME knob (1) clockwise to adjust volume.
Turn the same knob counterclockwise to reduce the sound level.
2) ASC (Automatic Squelch Control) ~ SQUELCH
Suppresses
undesirable background noises when there is no communication.
Squelch does not affect neither sound nor transmission power, but allows a
considerable improvement in listening comfort.
a) ASC: AUTOMATIC SQUELCH CONTROL
Worldwide patent, a PRESIDENT exclusivity
Turn the SQUELCH knob (2) anti-clockwise into ASC position.
on LCD. No repetitive manual adjustment and a permanent improvement
between the sensitivity and the listening comfort when ASC is active. This
function can be disconnected by turning the switch clockwise. In this case
the squelch adjustment becomes manual again.
b) MANUAL SQUELCH
Turn the SQUELCH knob (2) clockwise to the exact point where all background
noise disappears. This adjustment should be done with precision as, if set to
maximum (fully clockwise), only the strongest signals will be received.
3) RF POWER
In TX mode, turn the RF POWER knob (3) to
increase,
clockwise to counterclockwise to
4) MIC GAIN
Adjustment of the sensitivity level of the microphone.
The normal position of this function is set to maximum clockwise.
5) RF GAIN
Adjustment of the reception sensitivity. Maximum position in the case of long-
distance transmission. You can
when the interlocutor is near. Reduce the gain on reception in the case of a
close communication with a correspondent not equipped with a RF POWER.
The normal position of this function is at maximum clockwise.
6) ROTARY "PUSH" KNOB
In normal operation, turn rotary PUSH knob (6) to adjust channel. Clockwise
to increase, counterclockwise to
mode (long press PUSH knob (6) for 3 seconds to activate this
In MENU
mode). See § MENU page 10.
1. Turn rotary PUSH knob (6) to
2. Press PUSH knob (6) to validate. The parameter of the chosen function blinks
on LCD.
3. Turn rotary PUSH knob (6) to
4. New press PUSH knob (6) to
stops blinking and if the function has more than one parameter, the next
parameter blinks.
See § UP/DN BUTTONS ON THE MICROPHONE page 9.
7
disappears from LCD.
adjust the transmission power;
decrease the RF POWER.
decrease the RF GAIN, to avoid distortions,
decrease
the channel.
select
the function to set.
change
the value of the parameter.
validate the chosen value. The parameter
appears