PRESIDENT WALKER II FCC Manuel D'utilisation page 9

11) PRIORITY CHANNELS
Priority channels will be automatically
3 positions switch: EMG1/ Priority channel 1 is activated. EMG2 / Priority
channel 2 is activated. OFF / No priority channel is activated.
The default priority channels are channel 9 (EMG1) and channel 19 (EMG2).
See the EMG SET 1 and EMG SET 2 menus page 11 to
Note: Activating a priority channel no longer allows you to use the
modes, or to start the SCAN function. if the KEY BEEP function is active, an
error beep is emitted. "EMG" and the channel blink to indicate unauthorized
handling. Turn the switch (11) to the OFF position to use these functions.
12) CB/PA
CB PA
Switch between and (Public Address) mode.
An external optional speaker can be connected to the unit to the PA.SP.
jack on the rear panel. (D). Turn the MIC GAIN knob (4) to adjust the
volume.
For details on operating in PA mode, see the PA SETTING menu on page
12.
13) WX MODE ~ ALERT
WX MODE
(short press)
Note: CB
functions are not allowed in
lowed key when the KEY BEEP function is activated, the radio sounds an error
tone.
Select a channel other than the EMG1 or EMG2 emergency channels. The
PRIORITY CHANNEL switch (11) must be in the OFF position. Press briefly the
WX key (13) to alternate between
WX
active, "WX" is displayed.
When this mode is turned on, turn the rotary PUSH knob (6) or use the UP/DN
(18) keys on the microphone to search, through the 7 weather channels,
for the channel corresponding to your location (See WEATHER FREQUENCY
TABLE page 55).
The display shows the selected channel.
ALERT
(long press)
Note: The SIREN tone only sounds in
WX
mode.
Long press the ALERT key (13), to
When the function is activated the last digit of frequency becomes A
( ). If the function is activated and a tone is detected at
selected
by switching this key (11).
set priority channels.
WX
mode. If a user presses a not al-
CB WX modes. When WX mode is
and
mode allows you to listen to weather reports.
PA CB
or mode. It does not sound in
activate/deactivate the ALERT function.
the selected weather channel, then the unit sounds "SIREN" tone. The unit
CB PA
cancels or
During a SIREN tone sound, press PTT key (17) to stop the sound.
14) BARGRAPH
PA WX
or
Indicates the reception level and the emitted power level.
15) 6 PIN MICROPHONE PLUG
PA
The plug is located on the front panel of the transceiver and makes the
setting of the equipment into the dashboard easier.
See Cabling Diagram page 56.
16) USB CHARGING SOCKET
The USB socket (16) can be used to charge smartphones, tablets or other
rechargeable devices with 5 V - 2.1 A.
17) PTT
Transmission key, press to
to listen to an incoming communication,
TOT (Time Out Timer)
If the PTT switch (17) key is pressed for more than 5 minutes, the display starts
blinking and the transmission ends. A beep will sound until the PTT switch
(17) key is released.
18) UP/DN BUTTONS ON MICROPHONE ~ SCAN
UP/DN BUTTONS ON MICROPHONE
In normal use, press UP/DN buttons (18) on the microphone to
channel. UP to increase
In MENU mode [press the PUSH knob (6) for about 3 seconds to activate this
mode (see § MENU page 10)], the UP or DN buttons (18) allows to
the menu to be set.
See ROTARY "PUSH" KNOB page 7.
9
WX
mode and goes to mode.
transmit a message, is displayed and release
disappears.
(short press)
and DN to decrease
the channel.
change the
select