Publicité
Les langues disponibles
Les langues disponibles
5 - I
NSTALLING YOUR WINE CABINET
I - In General
- On unpacking you wine cabinet after delivery, check for any obvious exterior damage (dents, malformation, etc.).
- Open the door and check that the inside of the appliance is complete and in good condition (walls, shelves, hinges, control panel, etc.).
- In the event of a problem, contact your dealer.
- Move your wine cabinet to your selected location. This location should
- not be a confined space.There should be space to allow air to flow around the cabinet. (not placed in a cupboard, etc.)
- away from any heat source
- not too wet (wash room, utility room, bathroom, etc.)
- be on a flat solid floor
- have an electrical power supply (standard 13A plug connected to a 30 mA* circuit breaker)
* not applied to certain countries
- Never place your wine cabinet in a location liable to flooding.
- Avoid splashing water onto the base of the appliance.
- Place the clay humidity cassette (for 1 temperature models only), which you will find inside your cabinet's "accessories" box) in the receptacle provided for
it beneath the grid located at the base of the cabinet (see diagram page 20). For 2-
temperature models, the cassette is replaced by a clay cylinder (Hygro ++ cylinder) to be
placed on a shelf, amongst the bottles.When using the cassette for the first time, please
soak the cassette for ten minutes in water, and let it drain.
- Install the drip tray (which you will find inside your cabinet's "accessories" box) on the
compressor support at the back of the cabinet, locating it under the small pipe protruding
from the housing, the lower part of the tank being placed under this pipe (see diagram
opposite).
- Take the power lead (which you will find inside your cabinet's "accessories" box) and
connect it to the socket provided at the rear bottom left of the cabinet (see diagram
opposite).
- Unwind the power supply lead so that it can be accessed and place the appliance leaving a space between 8 and 10 cm
(3" 1/8 to 4") space between the wall and the back of your wine cabinet.
- Place the power supply lead so that it is not in contact with any of the appliance's components.
- I I M M P P O O R R T T A A N N T T - - W
W a a i i t t 4 4 8 8 h h o o u u r r s s b b e e f f o o r r e e s s w w i i t t c c h h i i n n g g o o n n t t o o a a l l l l o o w w t t h h e e f f l l u u i i d d s s c c o o n n t t a a i i n n e e d d i i n n t t h h e e i i n n t t e e r r n n a a l l c c i i r r c c u u i i t t s s t t o o s s e e t t t t l l e e . .
- Gently incline the wine cabinet backwards in order to adjust the front feet (screw adjustment) so that your wine cabinet
stands perfectly level (we recommend using a regular spirit level).
- Remove the protective items located inside your wine cabinet.
- Install the carbon filter, which you will find inside your cabinet's "accessories" box , by placing it in the air circulation hole
located inside the cabinet on the top left hand side (see diagram opposite).
- BEWARE: any changing of the control panel LED should only be carried out by a qualified electrician.
- Never connect several wine cabinets to a multi-socket and do not use an extension cord.
N.B.: when moving your wine cabinet, do not incline it more than 45°,and always
A wine cabinet must be designed in such a way that bottles do not come into contact with the rear wall. In
some circumstances, condensation created on the rear wall can trickle down onto the shelves and damage the
bottle labels. Also, contact with a cold wall can create a frost point which is harmful to the wine.
toward side where the power lead is located.
Did you know?
7 7
E E N N
Publicité
