Publicité
Les langues disponibles
Les langues disponibles
For a Blank of More Than 4 Seconds
During
recording, keep the rec mute
button pressed for a longer blank section.
Release the button to enter the record-
pause mode.
e For a Blank of Less Than 4 Seconds
After pressing
the
rec
mute
button
during recording,
press the rec mute
or pause button before the 4-second
interval has expired, to cancel the muting
mode
and engage the record-pause mode.
To restart recording press the
# or >
button.
Erasing
Previously
recorded
tapes will be erased
automatically when you make a new record-
ing. Alternatively, tapes can be erased by
"recording" on them with the rec level
control set to "oo",
Calibration Procedure
Each cassette tape has different characteris-
tics depending
on the manufacturer
and
type. By properly adjusting bias and level
(sensitivity) according to the tape, it is
possible to record making the most of the
tape's characteristics.
1, Load the cassette to be recorded.
2. Press the calibration start button.
me
(LEVEL, { light.)
. Press the record and > buttons to
start recording. The built-in test tone
will be recorded.
Adjust the level controls (of both the
L and R channels) so that the meter
deflection comes to the {| mark.
Gi
®©
o
>
mii
5. Press the calibration start button once
again.
woraci
(BIAS,
{ light)
2
} . Adjust the bias controls (of both L and
R channels) so that the meter deflec-
tion comes to the
| mark.
fa
passe
Now, the optimum bias and level (sen-
sitivity) have been set.
Press the stop button to end the
calibration.
Erase
the
recorded
test
tone
or rewind
the tape and record
over it.
To recheck level and bias, press the
calibration start button again.
Stick a seal, etc. on the front panel
around the level and bias controls to
facilitate setting the next time you
make a recording with the same type of
tape.
fe How to Select
any Required Tune Using CPS
Ex: See (1). To select the 3rd tune past the current tape position, select "CP03".
a
Current tape position
CPS (Computomatic Program
Search) Function
CPS
allows the selection
and playback
of any tune up to 15 tunes ahead or before
the one being played. This function operates
by detecting blank spaces of at least 4
seconds between tunes. These blanks can
be created using the rec mute facility.
1. Press the He< or >>! button repeated-
ly until the number
of tunes to be
skipped
appears
in the
multi-display
counter.
Refer to the chart "How to
Select any Required Tune Using CPS".
elf you count past the required number,
keep on pressing the CPS button
as 1
appears after 15 is indicated.
When
the
>!
button
is pressed, the
next tune is counted as '1' and when the
¢<
button is pressed, the current tune
is counted as "'1'"
2. As the tape is fast-forwarded or rewound
and
blank
spaces between
tunes are
detected,
the
displayed
number
will
be counted down until it reaches "1",
at which point playback will start.
Notes on CPS
CPS operates
by detecting and counting
blanks of about 4 seconds, normally the
intervals between
tunes. Therefore, with
the following types of tapes, search func-
tions may not work correctly.
@ When
the intervals
between
tunes
cannot be detected.
— Intervals of less than 4 seconds.
— High levels of noise in intervals.
— Long low level sections (in classical
music, etc.)
This problem can be corrected using the
REC MUTE function.
T
1 T
7
a
|
Direction of
\
|] Le
®
®
@
@ |
tape travel
eats
c=z
<=
Fotowing | Betore
In example (1). is lees than
1 sscane wit nat be Counted
as a blank.
Designate "CP02"
fstead of CPOs" To select the
Sid tune n tvs ease
@)
Current tape position
")
iN
im)
] [ ®
@
@
Direction of
L
tape travel
|
Following | Before
Publicité
