Teac V-8030S Manuel Du Propriétaire page 6

© CD direct Select Button
(See page 7.)
@ Cassette Holder
© margin reset
Press this button to release the peak hold
memory.
© Multi-Display Window
@) Peak Level Meter
This meter shows the peak level of
the input or playback signal. The
meter has a peak hold feature; when
the level exceeds ~7 dB, the peak level
is held for approx. 2 seconds.
(®) Tape Type Indicator
© Linear Counter
(© DOLBY NR [B\C)'S' Indicator
(© TAPE/SOURCE Indicator
Indicates whether the deck is set for
tape or source monitoring.
®
BIAS/LEVEL Indicator
Indicates the level (sensitivity) and
bias when calibration is performed.
CD SYNC Indicator
Lights when CD synchro start is
activated
(H) Level Indicator
The level shown by the Peak Level
Meter is indicated numerically from 0
to 11 dB. When the level reaches 12
dB or more, the OVER indicator comes
on and the level 11 dB stays lit until
the power is switched off or the
margin reset button is pressed
@ CD sync Button
(See page 9.)
@® CD check Button
(See page 7.)
® clear Button
Pressing the clear button resets the linear
counter to zero (0000).
® tape length Button
@ RTZ Button
(See page 9.)
@® Remote Sensor (Remote
Control Infrared Signal
Receptor)
® rec mute Button
(See page 7.)
@ phones Jack
Plug stereo headphones into this jack for
private listening or monitoring.
® Phones level Control
Adjust the level of the signals output from
the phones jack.
® balance Control
(See page 7.)
@ power Switch
Note: When switching the power on again
after switching it off, be sure to wait for
more than 3 seconds.
@ timer Switch
(See page 9.)
@® open/close Button
Press thes button to open or close the
Cassette holder. As this deck employs a
power loading mechanism, opening and
closing the cassette holder is possible
only when the power is on. Even if the
holder is open, it closes automatically and
the corresponding operation is performed
when the » button, etc. is pressed. The
cassette holder can also be closed
manually.
® < pp: (CPS) Button
(See page 8.)
® Tape Travel Operation Buttons
© stop Button (m)
© play Button (»>)
© pause Button (m)
@ record Button (@)
@ (<<) rewind Button
@ (me) fast-forward button
® display Button
Press this button to switch off the multi-
display indication (illumination).
Operations
Playback and Recording
tape length Button
The linear counter of this deck indicates
the recording/playback time in minute and
second. To minimize the error in the
counter reading due to the difference in
tape length (duration), be sure to press the
tape length button until the appropriate
tape length appears.
When the tape length button is pressed,
the linear counter will indicate the tape
length.
{Indication Cassette used
C60 | C-60/50, ete.
c-90 €-90/80, etc.
C46 | C-46/30/10, ete.
case — C46 large hub —_|
Since the linear counter is not a clock,
there is a discrepancy between the
actual recording/playback time and
counter reading
Once the power is switched off, "C-60"
appears when the power is switched
on again.
After setting is complete, the tape
length is indicated for approx. 5
seconds; after that, the counter
indication is resumed.
* Set the tape length again after a
cassette with a different length is
loaded or the power is switched on.
Stereo Playback
1. Press the power switch to ON.
2. Press the open/close button and load
the required cassette.
3. Set the tape length. (See previous
section.)
4. Select the required NR system
5. Press the » button to start playback.
6. Adjust the volume with the amplifier's
control
7. To end playback, press the stop (m)
button.