Whirlpool ED5FVGXWS02 Mode D'emploi page 16

Base Grille Water Filtration System
Model PIWG2L/P2RFWG2 Capacity 200 Gallons (757 Liters)
Model PIWG2/P2RFWG2 Capacity 200 Gallons (757 Liters)
System tested and certified by NSF International against NSF/ANSI
Standard 42 for the reduction of Chlorine Taste and Odor, Particulate
Class I*; and against NSF/ANSI Standard 53 for the reduction of Lead,
Mercury, Benzene, Toxaphene, and O-dichlorobenzene.
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The
concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the
permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.
Substance Reduction
Aesthetic Effects
Chlorine Taste/Odor
Particulate Class I*
Contaminant
Reduction
Lead: @ pH 6.5
Lead: @ pH 8.5
Mercury: @ pH 6.5
Mercury: @ pH 8.5
Benzene
O-Dichlorobenzene
Toxaphene
NSF Reduction
Requirements
50% reduction
85% reduction
NSF Reduction Average Influent Challenge
Requirements Influent Concentration
0.010 mg/L 143.33 ug/L 0.15 mg/L + 10%
0.010 mg/L 150 ug/L 0.15 mg/L _+10%
0.002 mg/L 0.0058 mg/L 0.006 mg/L + 10%
0.002 mg/L 0.00646 mg/L 0.006 mg/L_+ 10%
0.005 mg/L 0.015 mg/L 0.015 mg/L _+10%
0.6 mg/L 1.83333 mg/L 1.8 mg/L _+10%
0.003 mg/L 0.016 mg/L 0.015 mg/L _+10%
Average Influent Challenge Maximum Average
Influent Concentration Effluent Effluent
1.909 mg/L 2.0 mg/L + 10% 0.05 mg/L ** <0.05 mg/L
5166666 #/mL At east 10,000 part c es/mL 4200 #/mL 1900 #/mL
Maximum Average
Effluent Effluent
1.0 ug/L 1.0 ug/L
1.0 ug/L 1.0 ug/L
0.3 ug/L 0.0002 mg/L
0.8 ug/L 0.0004 mg/L
0.5 ug/L 0.0005 mg/L
160 ug/L 0.005 mg/L
1 ug/L 0.001 mg/L
Test Parameters: pH = 7.5 _+0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68°F to 71.6°F (2O°C to 22°C). Rated service capacity = 200 gallons (757 liters).
• It is essential that operational, maintenance, and filter •
replacement requirements be carried out for the product to
perform as advertised.
• Use replacement filter P2RFWG2, part #4396841.
2008 suggested retail price of $39.99 U.S.A./S54.95 Canada.
Prices are subject to change without notice.
Model PlWG2L/PlWG2: Style 1 - When the filter indicator
reads 10%, order a new filter. When the indicator reads 0%, it is
recommended that you replace the filter.
Style 2 - When the filter indicator changes from green to yellow,
order a new filter. When the indicator changes from yellow to red,
it is recommended that you replace the filter.
Style 3 - When the water filter status display changes from
"GOOD" to "ORDER," order a new filter. When the filter indicator
reads "REPLACE," it is recommended that you replace the filter.
Style 4 - Press FILTER to check the status of your water filter. If
the filter indicator light is yellow, order a new filter. If the filter
indicator light is red, it is recommended that you replace the filter.
Change the water filter cartridge every 6 months. If the water
flow to the water dispenser or ice maker decreases noticeably
before 6 months have passed, replace the water filter cartridge
more often.
Minimum %
Reduction
>97.4
>99.9
Minimum %
Reduction
>99.3
>99.3
94.8
88.5
>96.7
91.1
>93.8
Average %
Reduction
>97.4
>99.9
Average %
Reduction
>99.3
99.3
96.4
94.9
>96.7
96.5
>93.8
These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory
conditions, actual performance may vary.
• The product is for cold water use only.
• Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system.
• Refer to the "Warranty" section for the Manufacturer's name,
address and telephone number.
• Refer to the "Warranty" section for the Manufacturer's limited
warranty.
Application Guidelines/Water Supply Parameters
Water Supply City or Well
Water Pressure 30 - 120 psi (207 - 827 kPa)
Water Temperature 33 ° - 100°F (0.6 ° - 37.8°C)
Service Flow Rate 0.5 gpm (1.9 Lpm) @ 60 psi
*Class I particle size: >0.5 um to <1 um
**Test requirement is at least 100,OOO particles/mL of AC Fine Test Dust.
® NSF is a registered trademark of NSF International.
16