Argo DELUXE 9000 UI Manuel D'utilisation Et D'installation page 41

ELE.H function
With the unit turned on, press the Menu button and using the + - and U/D SWING or L/R SWING buttons select
the ELE.H function, pressing OK on the corresponding indication shown on the display. To deactivate this function,
again using the Menu button and the selection buttons, press OK on the ELE.H indication, which will turn off. This
function allows you to activate the auxiliary heating.
The unit will then activate the auxiliary heating function based on the temperature detected in the room, to speed
up heating and reach the desired temperature more quickly.
DISPLAY function
With the unit turned on, press the Menu button and using the + - and U/D SWING or L/R SWING buttons
select the DISPLAY function, pressing OK on the corresponding indication shown on the display. By subsequently
pressing the button, the display on the indoor unit turns off or on.
To deactivate this function, again using the Menu button and the selection buttons, press OK on the DISPLAY
indication, which will turn off. This function is used to activate or deactivate the display lighting on the indoor unit.
LIGHT function
Function not available.
iCLEAN function
With the unit turned off, press the Menu button using the + - and U/D SWING or L/R SWING buttons to select
the iCLEAN function, pressing OK on the corresponding indication shown on the display. The single CL appears
on the indoor unit display. To deactivate this function, again using the Menu button and the selection buttons, press
OK on the iCLEAN indication, which will turn off.
iCLEAN designed for thorough and effective cleaning of the evaporator which consists of 4 phases plus sterilization
at 57 °C. Evaporator cleaning can be activated when desired.
The function will see phases of condensation, ice formation, defrosting and drying take place in sequence aimed
at eliminating all residues of dust and pollutants and all traces of condensation: a fifth phase of sterilization will
follow in which the evaporating unit will be kept for at least 10 minutes at a temperature of 57 °C. This will allow
clean air to be introduced into the room at all times and to preserve the efficiency of the heat exchanger
I-FEEL function
With the unit turned on, press the Menu button and using the + - and U/D SWING or L/R SWING buttons select
the I-FEEL function, pressing OK on the I-FEEL indication will show the icon on the display. To deactivate this
function, again using the Menu button and the selection buttons, press OK on the I-FEEL indication, which will
turn off. Once this function is set, the remote control sends the detected room temperature to the indoor unit every
10 minutes, which will then adjust its operation automatically according to the difference between temperatures
detected and set temperature. Place the remote control near you when setting this function.
Do not place the remote control near high or low temperature objects to avoid detecting inaccurate room
temperature.
Anti-F function
With the unit turned off, press the Menu button and use the + - and U/D SWING or L/R SWING buttons to
select the Anti-F function, pressing OK on the corresponding indication shown on the remote control display. To
deactivate this function, again using the Menu button and the selection buttons, press OK on the Anti-F indication,
which will go off.
This air conditioner has a special drying and anti-mold function. Activate this function before turning off the unit to
ensure that the air conditioner, after operating in cooling, dehumidification or Auto mode, continues to ventilate for
three minutes at low speed before stopping. The purpose of this function is to perfectly dry the evaporator of the
internal unit and prevent the formation of mold and bacteria.
Functions that can be activated by button combination
CHILD LOCK function
Press the HEAT and MODE buttons on the remote control simultaneously for 3 seconds to activate or deactivate
the button lock on the remote control. The icon will appear on the remote control display
°C/°F function
The temperature is shown by default in °C. To switch to °F display, press the COOL and HEAT buttons simultaneously
for 3 seconds.
Note: When the temperature is set on the remote control, it will be shown on the indoor unit display.
V 11/23 41