Publicité
Les langues disponibles
Les langues disponibles
•
Make sure that the spark plug connector is firmly seated! Risk: Electric shock.
•
If the tank has to be emptied, this should be done in the open, and with a
cold engine. Take care to ensure that no fuel is spilt.
Always store the equipment in a clean state in a closed, dry room and
inaccessible to children.
Always remove the ignition key (if present) during storage, to prevent
unauthorised actuation of the starter or mower.
For reasons of warranty and safety, only genuine spare parts may be used.
Non-equivalent spare parts can damage the machine and are a safety hazard.
7 DESCRIPTION OF COMPONENTS
1
Safety control bar for motor stop
2
Vario actuation (depending on the model)
3
Drive control bar
4
Tank cap
5
Engine cover
6
Cutting height setting
7
Air filter
8
Carrying handle
9
Spark plug
10 Exhaust protection grid
11 Belt drive covers
12 Oil refill neck with dipstick
13 Ejector flap
14 Fast release (depending on the model)
15 Starter cable handle
16 Starter key (depending on the model)
8 PREPARATION
The following unit parts are included in the package for mower assembly:
•
Mower with pre-assembled guide bar
•
Grass catch, collecting bag frame
•
Tool bag containing the following:
–
Operator's manual with Declaration of Conformity
–
Warranty conditions (depending on model)
–
Diverse attachment parts.
Should a part be missing, please contact your professional dealership.
NOTE
Always remove the spark plug connector before fitting the bar and the starter
cable holder. Following assembly, at the latest before starting the engine, push
the spark plug connector back in place.
Raise the handlebar (Illustration A1 + B1 + V4 )
IMPORTANT
Make sure the throttle cables are not kinked or jammed when lifting the
handlebars.
IMPORTANT
Make sure that the cables are not pinched, squeezed, twisted or overstretched
when the handlebars are folded apart or collapsed! Always run the cables along
the outside of the bar connection. A damaged cable may result in a technical
defect of the equipment.
Pull the handlebar which is collapsed in a Z-shape upwards into place in the following
sequence:
–
First lift the bottom part of the handlebar A1 , push the ends of this bottom part as
far apart as necessary for the locking cams facing the inside to lock into the
respective bore holes B1 .
Three different handlebar heights can be set.
–
Tighten the handle nuts on both sides by hand B1 .
–
Lift the top part of the handlebar until the top part and the bottom part of the
handlebar are on the same level.
Illustration V4 :
–
The quick releases for attachment of the top part and the bottom part of the
handlebar are preset by the manufacturer.
1.
Pull the quick releases upwards to the handlebar.
2.
Tighten the screws hand-tight.
3.
Open the quick releases.
4.
Tighten the screws by a quarter to a half of a turn.
5.
Pull the quick releases up again and check whether the bars are tightly
connected, correct again if necessary.
–
Keep this setting. If the tension slacks over time, the screws have to be tightened
again.
CAUTION
When you activate the bar height adjustment, when loosening the grip nuts
B1 used to secure the bar bottom to the housing (only loosen sufficiently to
ensure that the bar can be moved freely) and snapping the locking cams out of
the drilled holes on the connecting bar, it is possible that unintentional upsetting
of the bar may occur. In addition, this may result in crushed points between the
bar bottom and the bar connection/housing. This may result in a risk of injury!
Handle starter assembly (Illustration L1 )
–
Remove the starter cable holder (1) from the tool bag.
–
Unscrew the nut until the two halves can be pushed over the bar.
–
There is a sticker (2) on the top bar showing the position of the starter cable
holder.
NOTE
For reasons of safety, the starter cable holder may only be fitted in the
prescribed position.
–
Push the motor stop safety control bar (3) onto the top part of the bar (4) and hold
it tight, pull the starter cable (5) out and insert it into the starter cable holder.
–
Fit the two halves (6) together, tighten the nut again. This prevents the starter
cable popping out.
The starter cable holder must be fitted / aligned in such a way that the starter cable
is freely accessible and does not rub against any other parts.
Attaching the grass collector to the mower (Illustration R1 + S1 )
–
First insert the grass bag frame with the clip forward into the grass bag. Please
make sure that the protective corners of the collection material cover the back
corners of the collecting bag frame. Align the upper seams of the bag with the clip.
–
Press the retaining profiles of the collecting sack onto the bars of the collecting
sack frame R1 .
–
Open the ejection flap of the mower upwards.
–
Pick up the collecting sack by the carrying strap, place the chute (1) R1 at the
collecting sack opening into the ejection flap and hang it in the mower casing with
its two side hooks upwards S1 .
–
Attach ejection flap to collector.
Adjusting the cutting height (Illustration I )
You can set the desired cutting height with the adjustment lever (1) on the left of the
mower.
–
Pull the lever out of the catch and latch again after a lateral move into the desired
position.
–
The marking on the left of the housing indicates the cutting height.
IMPORTANT
Mowing at the lowest cutting height should only be carried out on level and plane
lawns!
Please note that the lower cutting height settings may only be used for optimum
6
Safety instruction!
See table for explanation of symbols page 3
Publicité
