Télécharger Imprimer la page

Carrera RC Super Mario - Flying Cape Mario Instructions De Montage Et D'utilisation page 4

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 5
NOTE: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If the product does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures :
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and receiver.
• Connect the product into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IC statement
The device contain license-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Eco-
nomic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
1. The device must not cause interference;
2. The device must accept any interference, including interference that may cause undesired operation of the device.
CAN ICES-3 (B)/NMB-3(B)
Guidelines and warnings for the use of LiPo rechargeable batteries
• You have to charge the attached 3.7 V
and at a safe distance to flammable material.
• Never leave the battery unattended while it is charging
• After a flight, the rechargeable battery has to cool down to the ambient air temperature before charging it.
• You must always use the corresponding LiPo charging unit (USB cable / remote control). In case of
non-compliance with these directions there is a danger of fire resulting in a health risk and/or damage to
property. NEVER use any other battery charger.
• Should the rechargeable battery swell or deform while discharging or recharging, you have to immediately
stop charging or discharging the battery. Take the battery out as quickly and carefully as possible and place
it in a safe and open area offside any inflammable material and watch it for at least 15 minutes. In case you
continue charging or discharging a battery which has already started to swell or deform there is a danger of
fire! Even in case of slight deforming or ballooning the rechargeable battery has to be taken out of operation.
• Store the rechargeable battery at ambient temperature in a dry place.
• Always recharge the battery after use to prevent its becoming deep discharged. After use, the bat-
tery must be allowed to cool down for at least 20 minutes before it can be fully recharged. Recharge
the battery occasionally (suggested every 2–3 months). Supply terminals are not to be short-circuit-
ed. Failure to treat the battery as described above can lead to its becoming defective. Never leave
the battery unattended while it is being charged.
• When transporting or temporarily storing the rechargeable battery the temperature should be between
5-50°C. If possible, do not store the battery or the model in a car and do not expose it to direct sunlight. In
case the battery is broiled it can be damaged or catch fire.
Note: If the battery voltage/output is low you will recognise that a considerable trim and/or controlling is
necessary to avoid that the helicopter starts trundling. This usually occurs before reaching a battery voltage
of 3 V and it is a good moment to end the flight.
Contents of package
1x Helicopter
1
1x Controller
1x Display- & charging socket
1x USB charging cable
2x 1.5 V Micro AAA batteries (non-rechargeable)
Recharging the LiPo rechargeable battery
This toy contains batteries that are non-replaceable. Make sure you only charge the LiPo rechargeable battery
supplied with the LiPo charging unit also supplied (USB cable and remote control). In case you try to charge
the rechargeable battery with a different LiPo battery charger or any other battery charger, this might cause
serious damages. Please carefully read the previous chapter about warnings and guidelines on the usage of
rechargeable batteries before proceeding.
Charging via computer:
2
• Connect the USB charging cable with the USB port of a computer. The LED on the USB charger cable lights
green indicating that the charger unit is correctly connected to the computer. If you plug in a helicopter with
a discharged battery, the LED on the USB charging cable does not light up; this shows that the helicopter
battery is being charged. The USB charging cable and the charging socket on the helicopter are designed
to make incorrect connection impossible.
• It takes about 30 minutes to recharge a discharged battery (but NOT a deep-discharged one). When the
battery is fully charged, the LED display on the USB charger cable lights up green again.
Note: When supplied, the lipo-battery is already partially charged so the first charging cycle may well take less time.
It is essential to follow the connection sequence given above! If you have the charger cable only
connected to the helicopter, and not to a source of electricity, a green LED display indicates that there
is still power in the battery. The green LED display does not necessarily indicate the battery is still
adequately charged. While charging, the power switch must be in the "OFF" position.
Inserting the batteries in the remote control
Open the battery compartment with a screwdriver and insert the batteries in the remote control. Please
3
keep in mind the correct polarity. After having closed the compartment you can check all functions of the
remote control with the help of the power-switch on the front. With the power-switch turned ON and proper
functioning, the top center LED on the remote control will light up red. When the control LED flashes rapidly,
the batteries in the controller must be changed.
Frequency bind between model and remote control
The Carrera RC helicopter and the remote control are frequency bound at purchase. Should there occur
4
any problems with the communication between the Carrera RC helicopter and the remote control at the
beginning, please carry out a new frequency bind.
• Remove the model from its presentation plinth.
• Switch on the model at the ON/OFF switch.
• The LED in the helicopter now flashes in rhythmically-accelerating sequence.
• Switch on the controller at the ON/OFF switch. Slide the left joystick, i.e. the gas lever, completely to the
top and back down again into the zero position. The bond will take place automatically. While connecting,
the controller emits a signal tone.
• Hold the model so that the rotor blades are horizontal.
• Allow the helicopter a few moments until the system is correctly initialised and is ready for operation.
• The control LED now lights continuously once again, indicating that the connection is ended.
ENGLISH
180 mAh / 0.66Wh LiPo rechargeable battery in a safe place
Checklist for flight preparation
This checklist does not replace the contents of the operating instructions. Although it can be used as a quick-
start-guide we strongly advise to first read the operating instructions in detail before you proceed.
• Check the contents of the package
• Connect the charging unit to the source of power.
• Charge the lipo-battery as described in the section "Charging the lipo-battery".
• Fit two AAA batteries in the controller, making sure their polarity is correct.
• Look for a suitable environment for flying
4
• Proceed as described in
.
• Repeat the above points as required, if you wish to fly more helicopters at the same time.
• Check the control system
• Start the helicopter from one hand. At the same time, hold the controller in the other hand so that you can
take over control of the helicopter immediately.
WARNING! THE MODEL FLIES FORWARDS BY ITSELF AND CAN ONLY BE CONTROLLED IN HEIGHT
AND DIRECTION
• Make yourself familiar with the control system
• Trim the helicopter as necessary as described under "Controlling the helicopter".
• The helicopter is now ready to be flown.
• If the helicopter displays no functions, retry the above binding procedure.
• Fly the model
• Land the model
• Switch the model off at the ON/OFF switch (3 sec.).
• Always switch off the remote control last
Range of functions of the remote control
1. Antenna
5
2. Power switch (ON / OFF)
3. Control LED
4. Gas
5. Tail (spinning in circles)
6. Trimmer for tail
7. Battery compartment
3
Description of helicopter
1. Coaxial rotor system
6
2. Socket for charging the lipo-battery
3. Display- & charging socket
4. ON-/OFF switch
Controlling the helicopter
In case you don´t know the control functions of your Carrera RC helicopter yet, please take some min-
7
utes before the first flight in or to make yourself familiar with them. The descriptions left or right refer to
the view out of the cockpit (pilote´s view). Push the throttle up to increase the rotational speed of the main
rotor blades. Increase the rotational speed of the main rotor blades and the model will start to ascend.
If you push down the throttle and thus reduce the rotational speed of the main rotor blades the helicopter
will descend. When the model has lifted off the ground you can get it into stationary hovering without abrupt
ascending or descending by carefully moving the throttle upwards and downwards.
Move the right lever (tail) to the left and the helicopter's nose turns (yaws) round the main rotor's axis in
8
a circle to the left. Move the right lever (tail) to the right and the helicopter's nose turns (yaws) round the
main rotor's axis in a circle to the right. Use the trimmer for tail until you have reached a stable neutral position
of the helicopter when hovering, without moving the right lever (tail).
WARNING! THE MODEL FLIES FORWARDS BY ITSELF AND CAN ONLY BE CONTROLLED IN
9
HEIGHT AND DIRECTION
After having made yourself familiar with the main control functions and having chosen an appropriate area for
flying the helicopter, you can start the first flight.
Choosing the flight area
When being prepared for the first flight you should choose a closed room without any persons
10
or obstacles which is as big as possible. Due to the size and controllability of the helicopter
experienced pilotes may be able to fly the helicopter in relatively small rooms. For your first flights we
strongly recommend to choose a room with a minimum floor space of 5 x 6 metres and 2.40 metres of
height. After having trimmed your helicopter for flight and having made yourself familiar with the
controlling and its functions you may start flying in smaller and less open environments.
This toy is intended to be used in domestic area (house and garden) only.
Troubleshooting
Problem: Remote control does not work.
Cause:
The ON/OFF-power switch is turned "OFF".
Solution: Turn the ON/OFF-power switch "ON".
Cause:
The batteries have been wrongly inserted.
Solution: Check if the batteries have been correctly inserted.
Cause:
The batteries do not have enough power.
Solution: Insert new batteries.
Problem: The helicopter cannot be controlled with the remote control
Cause:
The power switch on the reomote control is turned "OFF".
Solution: First turn the power switch on the remote control "ON".
Cause:
The remote control is possibly not correctly frequency bound with the receiver on the helicopter.
Solution: Link as described in
4
.
Problem: The rotor blades do not rotate.
Cause:
The power switch on the model or the controller is at "OFF"
Solution: Turn the ON/OFF-power switch "ON".
Cause:
The rechargeable battery is too weak or has run out of power.
Solution: Charge the battery (see chapter "Charging the battery").
Problem: The helicopter does not lift.
Cause:
The rotor blades rotate too slowly.
Solution: Push the throttle up.
Cause:
The battery´s power is not sufficient.
Solution: Charge the battery (see chapter "Charging the battery").
Problem: During flight, the helicopter loses speed and height without any obvious reason.
Cause:
The battery is too weak.
Solution: Charge the battery (see chapter "Charging the battery").
4

Publicité

loading