Peg-Perego IGMD0009 Utilisation Et Entretien page 8

product must undergo sorted waste collection.
DISPOSAL OF THE BATTERY
• Help protect the environment.
• Used batteries must not be disposed of with
domestic waste.
• They can be left at a used battery or special waste
collection centre. Contact your local authorities for
more information.
BATTERY WARNINGS
Battery charging must be carried out and supervised
by adults only.
Do not allow children to play with the battery.
CHARGING THE BATTERY
• Charge the battery according to the instructions
enclosed with the battery charger and never for
more than 24 hours.
• To avoid damage, the battery should be charged as
soon as the vehicle starts to lose speed.
• If the vehicle is left unused for a long time,
remember to charge the battery and to keep it
disconnected from the electrical system. Repeat the
recharge procedure at least once every three
months.
• The battery must not be charged upside-down.
• Do not forget about the battery which is being
charged! Check it from time to time.
• Only use the battery charger provided and the
original PEG PEREGO battery.
• The battery is sealed and does not require
maintenance.
• Do not remove the battery charger from the
socket by pulling the cable.
• Do not move the toy by pulling the battery charger
cable.
• Do not cover the battery charger cable, as this
would cause it to overheat.
• Do not place the cable and/or battery on hot
surfaces.
• Take care on how and where you wrap the cable to
so as not to damage it or compromise its
operation.
WARNING
• THE BATTERY CONTAINS CORROSIVE TOXIC
SUBSTANCES.
DO NOT TAMPER WITH IT.
• The battery contains acid-based electrolytes.
• Do not create direct contact between the battery
terminals, avoid strong impacts: risk of explosion
and/or fire.
• While charging, the battery produces gas. Charge
the battery in a well-ventilated environment, away
from sources of heat and flammable materials.
• The flat battery must be removed from the vehicle.
• It is not advisable to bring the battery into contact
with clothes, as it could damage them.
• Only use batteries or accumulators of the
recommended kind.
IF THERE IS A BATTERY LEAK
Protect your eyes. Avoid direct contact with the
electrolyte. Protect your hands.
Put the battery in a plastic bag and follow the
instructions for battery disposal.
IF SKIN OR EYES COME INTO CONTACT WITH
THE ELECTROLYTE
Thoroughly rinse the area concerned with running
water.
Consult a doctor immediately.
IF THE ELECTROLYTE IS SWALLOWED
Rinse the mouth and spit out the water.
Consult a doctor immediately.
MAINTENANCE AND VEHICLE
CARE
• Do not disassemble or try to repair the vehicle on
your own. Contact an authorised Peg Perego
customer support centre.
• The toy should not be left anywhere with a
temperature below 0°C. If it were to be used
without being warmed up to a temperature above
0°C, irreversible damage could be caused to the
motors and batteries.
• Check the condition of the vehicle regularly, paying
particular attention to the electrical system, the
plug connections, the terminal protectors and the
battery charger. If defects are identified, the
electrical vehicle and the battery charger must not
be used.
• Always disconnect the battery charger from the toy
before carrying out cleaning, maintenance, or any
type of intervention.
• For repairs use only original PEG PEREGO spare
parts.
• PEG PEREGO do not accept any responsibility for
cases of tampering with the electrical system.
• Do not leave the batteries or the vehicle close to
sources of heat like radiators, fireplaces, etc.
• Protect the vehicle from water, rain, snow, etc.
Using the vehicle on sand or mud may damage the
buttons, motors and gears.
• Lubricate moving parts like bearings, steering, etc.
periodically with light oil.
• The vehicle surfaces can be cleaned with a damp
cloth and, if necessary, with non-abrasive domestic
cleaning products.
• Cleaning must only be carried out by adults.
• Never dismantle the vehicle mechanisms or
motors, unless authorized by PEG PEREGO.
RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.
CUSTOMER SERVICE
PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://www.pegperego.com
The item's serial number must always be quoted.
Refer to the last illustration in this manual to find
the serial number.
ASSEMBLY INSTRUCTIONS
WARNING
THE VEHICLE MUST BE ASSEMBLED BY ADULTS.
BEWARE WHEN EXTRACTING THE VEHICLE
FROM THE PACKAGING.
ALL THE NECESSARY SCREWS AND SMALL
COMPONENTS ARE STORED IN A BAG INSIDE
THE PACKAGING.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while
assembling the toy, given the risks caused by small
parts (ingestion hazard) and the plastic bags that
contain them (choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a
pair of pliers.
ASSEMBLY
1 • Attach one of the hub covers (with a square hole
in the middle) to one of the two wheels with a
square hole.
2 • Turn the wheel over and apply the driver shown
in the detail illustration (with the hexagonal end),
aligning the 4 pins with the holes in the wheel.
3 • Insert a self-locking cap with a square inside on
the conical bushing, as shown in the drawing.
• Put the square axle into the hole in the self-
locking cap and use the hammer to anchor the
two components in place.
4 • Put the axle into the wheel you have assembled,
on the hub cover side.
5 • Insert the axle and wheel into the hole in the
gearmotor on the back of the product.
• Align the pentagon in the gearmotor with the
pentagon of the driver. Push all the way in to set
in place.
6 • Join the remaining hub cover with the square
hole in the middle to the other wheel with the
square hole.
• Turn the wheel over and apply the driver shown
in the detail illustration (with the hexagonal end),
aligning the 4 pins with the holes in the wheel.
7 • Fit the wheel onto the axle, pushing the (round)
end of the driver all the way into the hole in the
body.
8 • Insert a self-locking cap with a square inside onto
the black press-stud.
9 • Place the product on its left side. Put the conical
bushing in place under the wheel resting on the
work surface, as shown in the drawing. Rest the
black press-stud on the upper wheel and use a
hammer to fix the wheel in place.
10 • Insert the wiring cable coming out of the body
into its housing on the upper part of the prong,
as shown in the figure.
11 • Insert the front prong into the body until the pin
fits into the bottom part of the front plate, as
shown in the figure. The prong's pin must fit into
the curved part (see detail).
12 • Insert the nut provided into its housing under
the front mud flap. Insert the threaded pin from
the opposite side.
13 • Screw in the threaded pin to anchor the prong in
place under the body, making sure that the nut
does not come out of its seat.
14 • Remove the LED system from the handlebar and
insert it into the front plate, as shown in the
figure.
15 • Apply the corresponding sticker (see sticker
sheet) before you assemble the headlight. Snap
the 4 hooks of the headlight in place on the
front plate.
16 • Press the front plate onto the lower part of the
prong, snapping the 2 hooks in place and making
sure that the light connector is inserted in its
housing.
17 • Connect the 2 connectors to the handlebar.
18 • Press the handlebar onto the 3 holes in the