Télécharger Imprimer la page

Güde SBM 1050 E Traduction Du Mode D'emploi D'origine page 17

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18
WARNING Read all safety warnings and all
instructions.  Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
Drill safety warnings
Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a „live" wire may
make exposed metal parts of the power tool „live" and
could give the operator an electric shock.
Additional Safety and Working
Instructions
Use protective equipment. Always wear safety
glasses when working with the machine. The use of
protective clothing is recommended, such as dust
mask, protective gloves, sturdy non-slip footwear
and ear defenders.
The dust produced when using this tool may be
harmful to health. Do not inhale the dust. Use a dust
absorption system and wear a suitable dust protec-
tion mask. Remove deposited dust thoroughly, e.g.
with a vacuum cleaner.
Always keep the connection cable from the working
area of the device. Always guide the cable back-
wards, away from the device!
Do not machine any materials that present a danger
to health (e.g. asbestos).
When working in walls ceiling, or floor, take care to
avoid electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device.
Unclamped workpieces can cause severe injury and
damage.
Please turn the device immediately off when the
tool used gets blocked! Do not turn the device on
again when the tool is still blocked. This could cause
bounce back with a high reaction moment. Determi-
ne and remove the cause of the blocking of the tool
used while respecting the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
Chips and splinters must not be removed while the
machine is running.
WARNING! Danger of burns
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
The appliance must not be used if damaged or safety
equipment is defective. Replace any worn-out and
damaged parts.
Do not use the device near flammable liquids or ga-
ses. Risk of fire and explosion in case of short circuit.
Do not let any metal parts reach the airing slots -
danger of short circuit!
Mains Connection
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
Connect only to single-phase AC system voltage as
indicated on the rating plate. It is also possible to
connect to sockets without an earthing contact as
the design conforms to safety class II.
Only plug-in when machine is switched off.
Maintenance
Unplug the machine before any work on it.
Repairs and works specified in these Instructions may
only be performed by qualified authorised staff.
Use only original accessories and original spare parts.
Keep the device, in particular the air vents, clean at all
times. Never spray water on the device body!
Do not clean the plastics with solvents, flammable or
toxic fluids. For cleaning, use a damp cloth only.
Caution! If the power cord of the appliance gets
damaged, it must be replaced by the manufacturer or
its customer service or a similarly qualified person to
avoid danger.
Only a regularly maintained and treated appliance
can serve as a satisfactory aid. Insufficient mainte-
nance and care can lead to unforeseen accidents and
injuries.
If necessary, a list of spare parts can be found at www.
guede.com.
ENGLISH
13

Publicité

loading

Ce manuel est également adapté pour:

58113