Télécharger Imprimer la page

Makita DMR300 Manuel D'instructions page 12

Radio chargeur de chantier
Masquer les pouces Voir aussi pour DMR300:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18
Charging with USB power supply
port
CAUTION:
Do not connect power source to
USB port. Otherwise there is risk of fire. The USB
port is only intended for charging lower voltage
device. Always place the cover onto the USB port
when not charging the lower voltage device.
CAUTION:
Do not insert a nail, wire, etc. into
USB power supply port. Otherwise a circuit short
may cause smoke and fire.
NOTICE:
Before connecting USB device to the
charger, always backup your data of USB device.
Otherwise your data may lose by any possibility.
NOTICE:
When not using or after charging, remove
the USB cable and close the cover.
NOTICE:
Do not connect this USB socket with your
PC USB port, as it is highly possible that it may cause
breakdown of the units.
NOTE: The charger may not supply power to some
USB devices.
There are USB power supply ports at the front and back
side of the radio. You can charge USB device through
the USB power supply port.
► Fig.10: 1. USB power supply port
1.
Connect the USB device, such as a MP3 or CD
player, to the USB power supply port using a USB cable
available in the market.
2.
Press the Power button
radio.
NOTE: No matter if the radio is AC powered or battery
powered, you can charge a USB device when the
radio is switched on and in FM radio mode, Bluetooth
mode, or AUX mode which is appeared when an
external audio source is connected.
NOTE: The maximum volume of the output power
speaker will decrease when your USB device is being
charged.
NOTE: The USB socket can provide max 2.4 A 5 V (2
port total) of electrical current.
to switch on the
12 ENGLISH
Charging the battery cartridge
To charge the battery cartridge with this radio, insert
the adaptor plug into the DC IN socket and then plug it
to the mains. After that, insert the battery cartridge to
the slot.
► Fig.11: 1. LXT battery cartridge 2. CXT battery car-
tridge 3. Indicator for battery status/capacity
The indicator for battery status/capacity blinks when the
battery cartridge is being charged. The charging status
is as follows:
Indicator for battery status/
capacity
(blinking)
(blinking)
(not blinking)
NOTICE:
You cannot charge LXT and CXT bat-
tery cartridges at the same time.
NOTE: It will take several seconds until the indicator
for battery status/capacity appears after the AC power
adaptor is plugged into the mains.
NOTE: If the AC power adaptor is disconnected from
the radio during battery charging, the radio turns off
for a few seconds and then automatically turns on
with the battery power supply.
Hook for the AC power adaptor
The hook on the back of the radio is useful for carrying
the AC power adaptor. When carrying, bundle the cords
and tie them with AC power adaptor using the band.
► Fig.12: 1. Hook 2. AC power adaptor 3. Band
NOTICE:
Do not store AC power adaptor in the
battery compartment. The cord may be pinched and
damaged when closing the battery cover.
NOTICE:
Always hold the handle when carrying
the radio.
NOTICE:
Be careful not to drop the AC power
adaptor hooked on the back of the radio.
Bottle cap opener
The bottle cap opener is provided on the back of the
radio.
► Fig.13: 1. Bottle cap opener
NOTICE:
Hold the radio firmly when using the
bottle cap opener. Failure to do so may cause the
radio tipped over and result in damage or malfunction.
NOTICE:
Be careful not to spill the beverage
onto the radio when opening the cap.
Charging status
Charging (less than 80%)
Charging (80% or more has
been charged)
Charged (100%)

Publicité

loading

Ce manuel est également adapté pour:

Dmr301