BH FITNESS H946 Instructions De Montage Et Utilisation page 11

Application:
Shake well before using.
Hold the can 20 to 30 cm away from the surface to be
sprayed using the extension tube.
Wait two minutes until the product stabilises.
Carefully spread with a clean cloth, leaving a light and
uniform coat over the surface, and wipe off any excess.
For areas with difficult access use a brush to apply the
product. Leave to dry for about 3 hours.
Handling Precautions
Avoid all ignition sources (spark or flame).
DO NOT allow the material to come in contact with
eyes or skin. Wear
equipment during handling. Keep the container
closed. Avoid breathing vapours or mists. Use only
with adequate ventilation. Wash
contaminated clothing thoroughly after handling.
Storage
Keep the product in a cool, well-ventilated area.
Avoid all ignition sources (spark or flame). Store
between 4.4ºC and 49ºC. Store all materials in a
dry, well-ventilated area. Avoid breathing vapours.
3.- Apply the BH indoor cycling protector (111) with a
clean cloth to polish the product.
Application: Application should be over the entire bike
while this is dry.
Spray the BH indoor cycling protector (111) over the
surface to be treated.
Then spread with a clean cloth. Wipe dry with the cloth.
Do not let the product self-dry.
Note: In case any part or component needs to be
replaced, follow the same operations described
above. Use only original BH spare parts.
PREVENTIVE MAINTENANCE OF THE MACHINE
Every class
1. The user must check that the apparatus is safe
and appropriate for exercise.
2. A cloth or towel should be used to remove
sweat after the session has ended.
Weekly for the first month
1. Check the tightness of the pedal and crank with
a torque wrench. The tightening torque must be 46
Nm.
Weekly
1. Thoroughly inspect each apparatus to make
sure it is in safe and proper working order. Check
screws, nuts and bolts, pedal cages, handlebar,
saddle, knobs, worn pedal straps etc.
2. Use warm water and a cloth to clean the parts
that are dirty or that are in continuous contact with
sweat.
3. If you need to use soap, use the gentle
MEGUIAR'S NXT soap, which will not damage the
paint. In this case follow with the BH indoor cycling
protector, cleaning the area with a clean, dry cloth.
Wipe dry after.
appropriate protective
hands and
Monthly
1. Check the tightness of the pedal and crank with a
torque wrench. The tightening torque must be 46
Nm.
2. Check and adjust the belt.
If the belt slips it will be necessary to tighten it:
- Remove the side covers (49) and loosen the nuts
a maximum of two turns, Fig 7.
- Tighten the small nuts with a spanner. Make sure
that the nut rotates the same number of turns on
both sides of the machine (generally 2 turns will be
sufficient) otherwise the drive sprocket might
become skewed, creating a lot more noise and
making it possible for the belt to fall off.
- Tighten up the nuts again and put the side covers
(49) back in place.
- Whenever the tension on the machine has been
adjusted, readjust the brakes as well.
3. Wax those areas that are in contact with sweat.
It is not necessary to wax the entire machine, but it
is very important to wax those areas that are in
direct contact with sweat, since these are more
vulnerable to rust.
Apply the BH indoor cycling protector, cleaning the
area with a clean, dry cloth. Wipe dry after.
4. The 3 tightening knobs should be loosened off
and sprayed with Wurth lubricant to ensure that
they remain operative.
Annually
1. Clean with MEGUIAR'S NXT, adding the soap
to water in a bowl. Shake to create foam. Apply
with a wet sponge and dry with a cloth.
2. The areas shown in Figures 11 to 16 should be
protected with BH rust inhibitor following the same
procedure and then left to dry for 3 hours.
3. Apply the BH indoor cycling protector to the
cleaned area with a clean, dry cloth. Wipe dry after
application.
WARNING: Failure to follow the cleaning and
maintenance instructions could result in a
reduced working life of the apparatus and
serious personal injury to the user. Failure to
follow these instructions will void the warranty.
NOT COVERED BY THE WARRANTY:
Improper maintenance.
Incorrect assembly by the purchaser.
Failure to follow the assembly instructions as stated
in the manual provided.
Damage caused by the cleats of the shoes.
Stretching exercises should be performed in a
suitable place and never on the machine.
Do not hesitate to get touch with the Technical
Assistance Service if you have any queries by
phoning customer services (see last page in manual)
BH RESERVES THE RIGHT TO MODIFY THE
SPECIFICATIONS OF ITS PRODUCTS WITHOUT
PRIOR NOTICE.
11