Güde BIG WHEELER 460 AP Mode D'emploi page 11

Add fuel outdoor only; do not smoke when adding
o
fuel.
Add fuel before device starting. Never take the
o
cover out and do not add fuel when the engine is
running or hot.
- If you spill the petrol do not try to start the device.
o
Take the device away and prevent generation of a
flammable source around the spilled petrol.
Secure the petrol tank is closed safely.
o
•
Always check whether the knife, knife bolts and cutting
equipment are not damaged or worn before using the
mower. Always replace any damaged and worn knives
and bolts in the entire set to prevent device unbalance.
Do not make any alterations to the safety device.
Regularly check their proper functioning.
•
Keep the device clean, with no grass, leaves or other
impurities. Always wipe any oil or petrol run out. Let the
mower cool down before storing to closed spaces.
• Be especially careful when changing direction on a
slope.
•
Never adjust the height of wheels when the engine is
running.
•
The grass catching device may lose its functioning any
throw away items due to wear or damage. Regularly
check the mower parts and, if necessary, replace them
with spare parts recommended by the manufacturer.
•
The mower knife is very sharp. Risk of injury! Be
especially careful at knife maintaining, wear protective
gloves or cover the knife-edges.
•
Do not change the basic engine adjustment and avoid
its overloading.
• Be especially watchful when turning the mower or
pulling it towards your body.
•
If it is necessary to incline or lift the mower to pass a
surface other than grass or when carrying the mower to
or from the area to be cut then cut off the knife.
•
Release the knives and engine clutches before
switching on.
• Start the engine in accordance with the operating
instructions and make sure your legs are in safe
distance from the knife.
• Do not incline the mower at starting except for cases
when it is necessary. Do not incline the mower more
than necessary in such a case and always lift the part
reversed from you.
•
Do not start the engine when standing in front of the
ejection outlet.
•
Never lift and transfer the mower with engine running.
• Lower the brake adjustment when the engine is off. If
the engine is equipped with a stop valve then close the
petrol supply after cutting.
• Move slowly if using an auxiliary trail seat.
ASSEMBLY / PREPARATION
All assembly and/or maintenance works may be
performed only when the motor is turned off!
Please read the entire operating instructions before
assembling or starting your new mower.
IMPORTANT: The mower is supplied without oil and
petrol.
UNPACK THE MOWER
Take the mower out of the board and check whether there
are any free parts left there.
Assembly of collecting bag (Fig. 2) (Fig. 3) (Fig. 4)
1. Take the collecting bag, corresponding
frame and plastic insert out of the package.
(Fig. 2)
2. Put the frame into the collecting bag while
paying attention to that the coupling at the
frame is outside the collecting bag. (Fig. 3)
3. Now fix the collecting bag at the frame.
(Fig. 4)
Assembly - Handle
IMPORTANT: Disassemble the handle with care to prevent
clamping or damage of the cables.
1. Lift the handle until it snaps in the working
position.
2. Remove the protection sleeve, lift the upper parts of the
handle and assemble it with the bottom part. Tighten
the safety bolts on both sides of the handle.
3. Remove the protection sleeve of the operation grab handle in
the upper part.
Operation
Operation lever (for automatic stopping) (12) – press
the lever towards the handle when starting. If you want to
switch the engine off release the lever.
Drive lever (13) - used when you want the mower to be
moving forward.
loslassen = release
nach oben drücken = push up
Use
1. Cutting (without grass catcher)
The cut grass is laid in strips.
2. Cutting and collecting
The grass is collected to the grass catcher (if the grass
is damp or wet it reduces the catcher capacity). If you
want to mount the catcher to the mower lift the cover
plate and hang the grass catcher.
DRIVE CONTROL
The self-propelling travel is controlled as follows: Press the
operation lever (lever for automatic stopping) (12) towards the
handle and simultaneously press the drive lever towards the
handle (13).
The forward movement is stopped by releasing the drive lever
(13).
CUTTING HEIGHT ADJUSTMENT
Depending on the cutting height required it is necessary to
adjust the height of wheels. Adjust the height with the lever (8)
as you wish. The middle position is most suitable at most
mowers.
11