Publicité
Les langues disponibles
Les langues disponibles
TDTR Towel Rails
Models
TDTR175C, TDTR175W, TDTR350C & TDTR350W
:
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Model
Rails
TDTR 175C
1
TDTR 175W
12
TDTR 350C
18
TDTR 350W
18
Important Safety Advice
WARNING - THE SURFACE OF THIS RADIATOR CAN BE
HOT.
In order to be effective the towel rail will get hot, however
momentary contact with any part of it should not cause
injury.
The heater is to be installed so that switches and other controls
cannot be touched by a person in the bath or shower.
CAUTION - This appliance is not intended for use by children
or other persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them from
using it safely. Children should be supervised to ensure that
they do not play with the appliance.
Precautions should be taken to ensure that prolonged contact
with the towel rail cannot occur. Particular care should be
taken in confined areas where accidental prolonged contact
with the rail could be more likely to occur.
This appliance should only be used to dry fabrics washed in
water using commonly available detergents.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
IMPORTANT - If the towel rail is to be installed in a place used
by the public, a warning notice should be placed adjacent to
the rail advising that the surface can be hot.
WARNING - The towel rail is a sealed unit and is filled and
sealed under controlled conditions. Under no circumstances
should the seal of the unit be compromised
WARNING - In order to avoid a hazard for very young children,
this appliance should be installed so that the lowest heated
rail is at least 600mm above the floor.
General
The TDTR towel rail is designed to provide an all year round service
for airing towels and articles of clothing. It is not intended to provide
a sole heating service, but the larger model will take the chill off an
average size bathroom, lavatory or en suite. Your rail will be in one of
two sizes and will have either silver chromium plated or white stove-
enamel finish.
No routine maintenance is necessary apart from occasional
cleaning.
Both models are splashproof to IPX4 standard.
Electrical
WARNING - This appliance must be earthed
The electrical installation of this towel rail must be carried out by a
competent electrician in accordance with the current I.E.E Regulations
for Electrical Equipment. The towel rail is suitable for use on an A.C.~
electrical supply. Before installation check that the supply voltage
corresponds with that marked on the rail.
IMPORTANT - The wires in the mains lead
with the following code:
BLUE
-
NEUTRAL
BROWN
-
LIVE
GREEN/ YELLOW
-
EARTH
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
All manuals and user guides at all-guides.com
Watts
W e i g h t ( k g )
120
6
175
6
250
11
350
11
are coloured in accordance
plug, proceed as follows:
The wire which is coloured GREEN and YELLOW must be connected
to the terminal in the plug which is marked with the letter E or by the
earth symbol
or coloured green or green and yellow.
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured black.
The wire which is coloured BROWN must be connected to the terminal
which is marked with the letter L or coloured red.
This appliance must only be used on A.C. mains supply of 230/240
Volts~.
Installation
If fitted in a room containing a bath or shower, to comply with the
current I.E.E. Regulations, a cable outlet will be necessary with the
supply to the heater controlled by a double-pole pullcord switch having
a contact separation of 3mm in each pole. The body of the switch
should be situated as to be normally inaccessible to a person using
a bath or shower.
IMPORTANT - Protect the electrical connection whilst handling
the towel rail.
The towel rail must be permanently fixed to the wall using the wall
brackets supplied. The rail must be mounted vertically as shown in
Fig.1, observing the minimum clearances stated.
WARNING - The towel rail is heavy. Care must be taken when lifting
and fitting the towel rail.
Wall mounting
he wall mounting accessory pack contains:
T
TDTR175 &
TDTR350 Models:
Procedure for wall mounting
Note: TDTR 175 can be fitted in arrangement (1) or (2) from below
Fig. 2, using either three or four wall mounting brackets. Four brackets
must be used on the TDTR350 models
Step 1
Mark suitable mounting hole positions for the fixing brackets (ensuring
they are horizontal) - see Fig. 2, ensure to allow enough room above
and below to maintain the minimum clearance stated - see Fig.1.
Step 2
Drill and plug the wall to suit - see Fig. 3.
Step 3
Secure the outer wall bracket sleeves (a) to the wall using the screws
provided - see Fig. 3.
Step 4
Attach the inner wall bracket sleeves (b) to the towel rail with the
clamping pieces (c & d) and screw (e) as shown in Fig. 4.
Ensure the clamping pieces are aligned correctly as shown (x & y). The
screw should be left loose enough to allow horizontal adjustment.
Step 5
Align the wall bracket sleeves on the towel rail according to the
dimensions shown in Fig. 2.
Step 6
Lift the towel rail complete with the inner sleeve assembly and align
with the outer sleeve previously fixed to the wall.
sleeves are inserted correctly into the outer sleeves, determine the
desired distance of the rail from the wall and secure in place using the
fixing screw (f) - see Fig. 5.
-1-
UK
Class 1 IPX4
(a) 4 mounting brackets
(c) 4 wall mounting screws,
washers & wall plugs
(d) 4 depth adjusting
screws
When all the inner
Publicité
